src/spec/testing_stage1.py

   1 #!/usr/bin/env python3
   2 """
   3 pinmux documented here https://libre-soc.org/docs/pinmux/
   4 """
   5 from nmigen.build.dsl import Resource, Subsignal, Pins
   6 from nmigen.build.plat import TemplatedPlatform
   7 from nmigen.build.res import ResourceManager, ResourceError
   8 from nmigen.hdl.rec import Layout
   9 from nmigen import Elaboratable, Signal, Module, Instance
  10 from collections import OrderedDict
  11 from jtag import JTAG, resiotypes
  12 from copy import deepcopy
  13 from nmigen.cli import rtlil
  14 import sys
  15
  16 # extra dependencies for jtag testing (?)
  17 #from soc.bus.sram import SRAM
  18
  19 #from nmigen import Memory
  20 from nmigen.sim import Simulator, Delay, Settle, Tick, Passive
  21
  22 from nmutil.util import wrap
  23
  24 #from soc.debug.jtagutils import (jtag_read_write_reg,
  25 #                                 jtag_srv, jtag_set_reset,
  26 #                                 jtag_set_ir, jtag_set_get_dr)
  27
  28 from soc.debug.test.test_jtag_tap import (jtag_read_write_reg,
  29                                           jtag_set_reset,
  30                                           jtag_set_shift_ir,
  31                                           jtag_set_shift_dr,
  32                                           jtag_set_run,
  33                                           jtag_set_idle)
  34
  35 from c4m.nmigen.jtag.tap import TAP, IOType
  36 from c4m.nmigen.jtag.bus import Interface as JTAGInterface
  37 from soc.debug.dmi import DMIInterface, DBGCore
  38 #from soc.debug.test.dmi_sim import dmi_sim
  39 #from soc.debug.test.jtagremote import JTAGServer, JTAGClient
  40 from nmigen.build.res import ResourceError
  41
  42 # Was thinking of using these functions, but skipped for simplicity for now
  43 # XXX nope.  the output from JSON file.
  44 #from pinfunctions import (i2s, lpc, emmc, sdmmc, mspi, mquadspi, spi,
  45 # quadspi, i2c, mi2c, jtag, uart, uartfull, rgbttl, ulpi, rgmii, flexbus1,
  46 # flexbus2, sdram1, sdram2, sdram3, vss, vdd, sys, eint, pwm, gpio)
  47
  48 # File for stage 1 pinmux tested proposed by Luke,
  49 # https://bugs.libre-soc.org/show_bug.cgi?id=50#c10
  50
  51
  52 def dummy_pinset():
  53     # sigh this needs to come from pinmux.
  54     gpios = []
  55     for i in range(4):
  56         gpios.append("%d*" % i)
  57     return {'uart': ['tx+', 'rx-'],
  58             'gpio': gpios,
  59             #'jtag': ['tms-', 'tdi-', 'tdo+', 'tck+'],
  60             'i2c': ['sda*', 'scl+']}
  61
  62 """
  63 a function is needed which turns the results of dummy_pinset()
  64 into:
  65
  66 [UARTResource("uart", 0, tx=..., rx=..),
  67  I2CResource("i2c", 0, scl=..., sda=...),
  68  Resource("gpio", 0, Subsignal("i"...), Subsignal("o"...)
  69  Resource("gpio", 1, Subsignal("i"...), Subsignal("o"...)
  70  ...
  71 ]
  72 """
  73
  74
  75 def create_resources(pinset):
  76     resources = []
  77     for periph, pins in pinset.items():
  78         print(periph, pins)
  79         if periph == 'i2c':
  80             #print("I2C required!")
  81             resources.append(I2CResource('i2c', 0, sda='sda', scl='scl'))
  82         elif periph == 'uart':
  83             #print("UART required!")
  84             resources.append(UARTResource('uart', 0, tx='tx', rx='rx'))
  85         elif periph == 'gpio':
  86             #print("GPIO required!")
  87             print ("GPIO is defined as '*' type, meaning i, o and oe needed")
  88             ios = []
  89             for pin in pins:
  90                 pname = "gpio"+pin[:-1] # strip "*" on end
  91                 # urrrr... tristsate and io assume a single pin which is
  92                 # of course exactly what we don't want in an ASIC: we want
  93                 # *all three* pins but the damn port is not outputted
  94                 # as a triplet, it's a single Record named "io". sigh.
  95                 # therefore the only way to get a triplet of i/o/oe
  96                 # is to *actually* create explicit triple pins
  97                 # XXX ARRRGH, doesn't work
  98                 #pad = Subsignal("io",
  99                 #            Pins("%s_i %s_o %s_oe" % (pname, pname, pname),
 100                 #                 dir="io", assert_width=3))
 101                 #ios.append(Resource(pname, 0, pad))
 102                 pads = []
 103                 pads.append(Subsignal("i",
 104                             Pins(pname+"_i", dir="i", assert_width=1)))
 105                 pads.append(Subsignal("o",
 106                             Pins(pname+"_o", dir="o", assert_width=1)))
 107                 pads.append(Subsignal("oe",
 108                             Pins(pname+"_oe", dir="o", assert_width=1)))
 109                 ios.append(Resource.family(pname, 0, default_name=pname,
 110                                                  ios=pads))
 111             resources.append(Resource.family(periph, 0, default_name="gpio",
 112                                              ios=ios))
 113
 114     # add clock and reset
 115     clk = Resource("clk", 0, Pins("sys_clk", dir="i"))
 116     rst = Resource("rst", 0, Pins("sys_rst", dir="i"))
 117     resources.append(clk)
 118     resources.append(rst)
 119     return resources
 120
 121
 122 def JTAGResource(*args):
 123     io = []
 124     io.append(Subsignal("tms", Pins("tms", dir="i", assert_width=1)))
 125     io.append(Subsignal("tdi", Pins("tdi", dir="i", assert_width=1)))
 126     io.append(Subsignal("tck", Pins("tck", dir="i", assert_width=1)))
 127     io.append(Subsignal("tdo", Pins("tdo", dir="o", assert_width=1)))
 128     return Resource.family(*args, default_name="jtag", ios=io)
 129
 130 def UARTResource(*args, rx, tx):
 131     io = []
 132     io.append(Subsignal("rx", Pins(rx, dir="i", assert_width=1)))
 133     io.append(Subsignal("tx", Pins(tx, dir="o", assert_width=1)))
 134     return Resource.family(*args, default_name="uart", ios=io)
 135
 136
 137 def I2CResource(*args, scl, sda):
 138     ios = []
 139     pads = []
 140     pads.append(Subsignal("i", Pins(sda+"_i", dir="i", assert_width=1)))
 141     pads.append(Subsignal("o", Pins(sda+"_o", dir="o", assert_width=1)))
 142     pads.append(Subsignal("oe", Pins(sda+"_oe", dir="o", assert_width=1)))
 143     ios.append(Resource.family(sda, 0, default_name=sda, ios=pads))
 144     pads = []
 145     pads.append(Subsignal("i", Pins(scl+"_i", dir="i", assert_width=1)))
 146     pads.append(Subsignal("o", Pins(scl+"_o", dir="o", assert_width=1)))
 147     pads.append(Subsignal("oe", Pins(scl+"_oe", dir="o", assert_width=1)))
 148     ios.append(Resource.family(scl, 0, default_name=scl, ios=pads))
 149     return Resource.family(*args, default_name="i2c", ios=ios)
 150
 151
 152 # top-level demo module.
 153 class Blinker(Elaboratable):
 154     def __init__(self, pinset, resources, no_jtag_connect=False):
 155         self.no_jtag_connect = no_jtag_connect
 156         self.jtag = JTAG({}, "sync", resources=resources)
 157         #memory = Memory(width=32, depth=16)
 158         #self.sram = SRAM(memory=memory, bus=self.jtag.wb)
 159
 160     def elaborate(self, platform):
 161         jtag_resources = self.jtag.pad_mgr.resources
 162         m = Module()
 163         m.submodules.jtag = self.jtag
 164         #m.submodules.sram = self.sram
 165
 166         #count = Signal(5)
 167         #m.d.sync += count.eq(count+1)
 168         print ("resources", platform, jtag_resources.items())
 169         gpio = self.jtag.request('gpio')
 170         print (gpio, gpio.layout, gpio.fields)
 171         # get the GPIO bank, mess about with some of the pins
 172         #m.d.comb += gpio.gpio0.o.eq(1)
 173         #m.d.comb += gpio.gpio1.o.eq(gpio.gpio2.i)
 174         #m.d.comb += gpio.gpio1.oe.eq(count[4])
 175         #m.d.sync += count[0].eq(gpio.gpio1.i)
 176
 177         num_gpios = 4
 178         gpio_i_ro = Signal(num_gpios)
 179         gpio_o_test = Signal(num_gpios)
 180         gpio_oe_test = Signal(num_gpios)
 181
 182         # Create a read-only copy of core-side GPIO input signals
 183         # for Simulation asserts
 184         m.d.comb += gpio_i_ro[0].eq(gpio.gpio0.i)
 185         m.d.comb += gpio_i_ro[1].eq(gpio.gpio1.i)
 186         m.d.comb += gpio_i_ro[2].eq(gpio.gpio2.i)
 187         m.d.comb += gpio_i_ro[3].eq(gpio.gpio3.i)
 188
 189         # Wire up the output signal of each gpio by XOR'ing each bit of
 190         # gpio_o_test with gpio's input
 191         # Wire up each bit of gpio_oe_test signal to oe signal of each gpio.
 192         # Turn into a loop at some point, probably a way without
 193         # using get_attr()
 194         m.d.comb += gpio.gpio0.o.eq(gpio_o_test[0] ^ gpio.gpio0.i)
 195         m.d.comb += gpio.gpio1.o.eq(gpio_o_test[1] ^ gpio.gpio1.i)
 196         m.d.comb += gpio.gpio2.o.eq(gpio_o_test[2] ^ gpio.gpio2.i)
 197         m.d.comb += gpio.gpio3.o.eq(gpio_o_test[3] ^ gpio.gpio3.i)
 198
 199         m.d.comb += gpio.gpio0.oe.eq(gpio_oe_test[0])
 200         m.d.comb += gpio.gpio1.oe.eq(gpio_oe_test[1])
 201         m.d.comb += gpio.gpio2.oe.eq(gpio_oe_test[2])
 202         m.d.comb += gpio.gpio3.oe.eq(gpio_oe_test[3])
 203
 204         # get the UART resource, mess with the output tx
 205         uart = self.jtag.request('uart')
 206         print ("uart fields", uart, uart.fields)
 207         self.intermediary = Signal()
 208         m.d.comb += uart.tx.eq(self.intermediary)
 209         m.d.comb += self.intermediary.eq(uart.rx)
 210
 211         # I2C
 212         num_i2c = 1
 213         i2c_sda_oe_test = Signal(num_i2c)
 214         i2c_scl_oe_test = Signal(num_i2c)
 215         i2c = self.jtag.request('i2c')
 216         print ("i2c fields", i2c, i2c.fields)
 217         # Connect in loopback
 218         m.d.comb += i2c.scl.o.eq(i2c.scl.i)
 219         m.d.comb += i2c.sda.o.eq(i2c.sda.i)
 220         # Connect output enable to test port for sim
 221         m.d.comb += i2c.sda.oe.eq(i2c_sda_oe_test)
 222         m.d.comb += i2c.scl.oe.eq(i2c_scl_oe_test)
 223
 224         # to even be able to get at objects, you first have to make them
 225         # available - i.e. not as local variables
 226         # Public attributes are equivalent to input/output ports in hdl's
 227         self.gpio = gpio
 228         self.uart = uart
 229         self.i2c = i2c
 230         self.i2c_sda_oe_test = i2c_sda_oe_test
 231         self.i2c_scl_oe_test = i2c_scl_oe_test
 232         self.gpio_i_ro = gpio_i_ro
 233         self.gpio_o_test = gpio_o_test
 234         self.gpio_oe_test = gpio_oe_test
 235
 236         # sigh these wire up to the pads so you cannot set Signals
 237         # that are already wired
 238         if self.no_jtag_connect: # bypass jtag pad connect for testing purposes
 239             return m
 240         return self.jtag.boundary_elaborate(m, platform)
 241
 242     def ports(self):
 243         return list(self)
 244
 245     def __iter__(self):
 246         yield from self.jtag.iter_ports()
 247
 248 '''
 249     _trellis_command_templates = [
 250         r"""
 251         {{invoke_tool("yosys")}}
 252             {{quiet("-q")}}
 253             {{get_override("yosys_opts")|options}}
 254             -l {{name}}.rpt
 255             {{name}}.ys
 256         """,
 257     ]
 258 '''
 259
 260 # sigh, have to create a dummy platform for now.
 261 # TODO: investigate how the heck to get it to output ilang. or verilog.
 262 # or, anything, really.  but at least it doesn't barf
 263 class ASICPlatform(TemplatedPlatform):
 264     connectors = []
 265     resources = OrderedDict()
 266     required_tools = []
 267     command_templates = ['/bin/true'] # no command needed: stops barfing
 268     file_templates = {
 269         **TemplatedPlatform.build_script_templates,
 270         "{{name}}.il": r"""
 271             # {{autogenerated}}
 272             {{emit_rtlil()}}
 273         """,
 274         "{{name}}.debug.v": r"""
 275             /* {{autogenerated}} */
 276             {{emit_debug_verilog()}}
 277         """,
 278     }
 279     toolchain = None
 280     default_clk = "clk" # should be picked up / overridden by platform sys.clk
 281     default_rst = "rst" # should be picked up / overridden by platform sys.rst
 282
 283     def __init__(self, resources, jtag):
 284         self.jtag = jtag
 285         super().__init__()
 286
 287         # create set of pin resources based on the pinset, this is for the core
 288         #jtag_resources = self.jtag.pad_mgr.resources
 289         self.add_resources(resources)
 290
 291         # add JTAG without scan
 292         self.add_resources([JTAGResource('jtag', 0)], no_boundary_scan=True)
 293
 294     def add_resources(self, resources, no_boundary_scan=False):
 295         print ("ASICPlatform add_resources", resources)
 296         return super().add_resources(resources)
 297
 298     #def iter_ports(self):
 299     #    yield from super().iter_ports()
 300     #    for io in self.jtag.ios.values():
 301     #        print ("iter ports", io.layout, io)
 302     #        for field in io.core.fields:
 303     #            yield getattr(io.core, field)
 304     #        for field in io.pad.fields:
 305     #            yield getattr(io.pad, field)
 306
 307     # XXX these aren't strictly necessary right now but the next
 308     # phase is to add JTAG Boundary Scan so it maaay be worth adding?
 309     # at least for the print statements
 310     def get_input(self, pin, port, attrs, invert):
 311         self._check_feature("single-ended input", pin, attrs,
 312                             valid_xdrs=(0,), valid_attrs=None)
 313
 314         m = Module()
 315         print ("    get_input", pin, "port", port, port.layout)
 316         m.d.comb += pin.i.eq(self._invert_if(invert, port))
 317         return m
 318
 319     def get_output(self, pin, port, attrs, invert):
 320         self._check_feature("single-ended output", pin, attrs,
 321                             valid_xdrs=(0,), valid_attrs=None)
 322
 323         m = Module()
 324         print ("    get_output", pin, "port", port, port.layout)
 325         m.d.comb += port.eq(self._invert_if(invert, pin.o))
 326         return m
 327
 328     def get_tristate(self, pin, port, attrs, invert):
 329         self._check_feature("single-ended tristate", pin, attrs,
 330                             valid_xdrs=(0,), valid_attrs=None)
 331
 332         print ("    get_tristate", pin, "port", port, port.layout)
 333         m = Module()
 334         print ("       pad", pin, port, attrs)
 335         print ("       pin", pin.layout)
 336         return m
 337         #    m.submodules += Instance("$tribuf",
 338         #        p_WIDTH=pin.width,
 339         #        i_EN=pin.oe,
 340         #        i_A=self._invert_if(invert, pin.o),
 341         #        o_Y=port,
 342         #    )
 343         m.d.comb += io.core.o.eq(pin.o)
 344         m.d.comb += io.core.oe.eq(pin.oe)
 345         m.d.comb += pin.i.eq(io.core.i)
 346         m.d.comb += io.pad.i.eq(port.i)
 347         m.d.comb += port.o.eq(io.pad.o)
 348         m.d.comb += port.oe.eq(io.pad.oe)
 349         return m
 350
 351     def get_input_output(self, pin, port, attrs, invert):
 352         self._check_feature("single-ended input/output", pin, attrs,
 353                             valid_xdrs=(0,), valid_attrs=None)
 354
 355         print ("    get_input_output", pin, "port", port, port.layout)
 356         m = Module()
 357         print ("       port layout", port.layout)
 358         print ("       pin", pin)
 359         print ("            layout", pin.layout)
 360         #m.submodules += Instance("$tribuf",
 361         #    p_WIDTH=pin.width,
 362         #    i_EN=io.pad.oe,
 363         #    i_A=self._invert_if(invert, io.pad.o),
 364         #    o_Y=port,
 365         #)
 366         # Create aliases for the port sub-signals
 367         port_i = port.io[0]
 368         port_o = port.io[1]
 369         port_oe = port.io[2]
 370
 371         m.d.comb += pin.i.eq(self._invert_if(invert, port_i))
 372         m.d.comb += port_o.eq(self._invert_if(invert, pin.o))
 373         m.d.comb += port_oe.eq(pin.oe)
 374
 375         return m
 376
 377     def toolchain_prepare(self, fragment, name, **kwargs):
 378         """override toolchain_prepare in order to grab the fragment
 379         """
 380         self.fragment = fragment
 381         return super().toolchain_prepare(fragment, name, **kwargs)
 382
 383
 384
 385 def test_case0():
 386     print("Starting sanity test case!")
 387     print("printing out list of stuff in top")
 388     print ("JTAG IOs", top.jtag.ios)
 389     # ok top now has a variable named "gpio", let's enumerate that too
 390     print("printing out list of stuff in top.gpio and its type")
 391     print(top.gpio.__class__.__name__, dir(top.gpio))
 392     # ok, it's a nmigen Record, therefore it has a layout.  let's print
 393     # that too
 394     print("top.gpio is a Record therefore has fields and a layout")
 395     print("    layout:", top.gpio.layout)
 396     print("    fields:", top.gpio.fields)
 397     print("Fun never ends...")
 398     print("    layout, gpio2:", top.gpio.layout['gpio2'])
 399     print("    fields, gpio2:", top.gpio.fields['gpio2'])
 400     print(top.jtag.__class__.__name__, dir(top.jtag))
 401     print("Pads:")
 402     print(top.jtag.resource_table_pads[('gpio', 0)])
 403
 404     # etc etc. you get the general idea
 405     delayVal = 0.2e-6
 406     yield top.uart.rx.eq(0)
 407     yield Delay(delayVal)
 408     yield Settle()
 409     yield top.gpio.gpio2.o.eq(0)
 410     yield top.gpio.gpio3.o.eq(1)
 411     yield
 412     yield top.gpio.gpio3.oe.eq(1)
 413     yield
 414     yield top.gpio.gpio3.oe.eq(0)
 415     # grab the JTAG resource pad
 416     gpios_pad = top.jtag.resource_table_pads[('gpio', 0)]
 417     yield gpios_pad.gpio3.i.eq(1)
 418     yield Delay(delayVal)
 419     yield Settle()
 420     yield top.gpio.gpio2.oe.eq(1)
 421     yield top.gpio.gpio3.oe.eq(1)
 422     yield gpios_pad.gpio3.i.eq(0)
 423     yield top.jtag.gpio.gpio2.i.eq(1)
 424     yield Delay(delayVal)
 425     yield Settle()
 426     gpio_o2 = 0
 427     for _ in range(20):
 428         # get a value first (as an integer).  you were trying to set
 429         # it to the actual Signal.  this is not going to work.  or if
 430         # it does, it's very scary.
 431         gpio_o2 = not gpio_o2
 432         yield top.gpio.gpio2.o.eq(gpio_o2)
 433
 434         # ditto: here you are trying to set to an AST expression
 435         # which is inadviseable (likely to fail)
 436         gpio_o3 = not gpio_o2
 437         yield top.gpio.gpio3.o.eq(gpio_o3)
 438         yield Delay(delayVal)
 439         yield Settle()
 440         # grab the JTAG resource pad
 441         uart_pad = top.jtag.resource_table_pads[('uart', 0)]
 442         yield uart_pad.rx.i.eq(gpio_o2)
 443         yield Delay(delayVal)
 444         yield Settle()
 445         yield # one clock cycle
 446         tx_val = yield uart_pad.tx.o
 447         print ("xmit uart", tx_val, gpio_o2)
 448
 449     print ("jtag pad table keys")
 450     print (top.jtag.resource_table_pads.keys())
 451     uart_pad = top.jtag.resource_table_pads[('uart', 0)]
 452     print ("uart pad", uart_pad)
 453     print ("uart pad", uart_pad.layout)
 454
 455     yield top.gpio.gpio2.oe.eq(0)
 456     yield top.gpio.gpio3.oe.eq(0)
 457     yield top.jtag.gpio.gpio2.i.eq(0)
 458     yield Delay(delayVal)
 459     yield Settle()
 460
 461 # Code borrowed from cesar, runs, but shouldn't actually work because of
 462 # self. statements and non-existent signal names.
 463 def test_case1():
 464     print("Example test case")
 465     yield Passive()
 466     while True:
 467         # Settle() is needed to give a quick response to
 468         # the zero delay case
 469         yield Settle()
 470         # wait for rel_o to become active
 471         while not (yield self.rel_o):
 472             yield
 473             yield Settle()
 474         # read the transaction parameters
 475         assert self.expecting, "an unexpected result was produced"
 476         delay = (yield self.delay)
 477         expected = (yield self.expected)
 478         # wait for `delay` cycles
 479         for _ in range(delay):
 480             yield
 481         # activate go_i for one cycle
 482         yield self.go_i.eq(1)
 483         yield self.count.eq(self.count + 1)
 484         yield
 485         # check received data against the expected value
 486         result = (yield self.port)
 487         assert result == expected,\
 488             f"expected {expected}, received {result}"
 489         yield self.go_i.eq(0)
 490         yield self.port.eq(0)
 491
 492 def test_gpios(dut):
 493     print("Starting GPIO test case!")
 494
 495     num_gpios = dut.gpio_o_test.width
 496     # Grab GPIO outpud pad resource from JTAG BS - end of chain
 497     print (dut.jtag.boundary_scan_pads.keys())
 498     gpio0_o = dut.jtag.boundary_scan_pads['gpio_0__gpio0__o']['o']
 499     gpio1_o = dut.jtag.boundary_scan_pads['gpio_0__gpio1__o']['o']
 500     gpio2_o = dut.jtag.boundary_scan_pads['gpio_0__gpio2__o']['o']
 501     gpio3_o = dut.jtag.boundary_scan_pads['gpio_0__gpio3__o']['o']
 502     gpio_pad_out = [ gpio0_o, gpio1_o, gpio2_o, gpio3_o]
 503
 504     # Grab GPIO output enable pad resource from JTAG BS - end of chain
 505     gpio0_oe = dut.jtag.boundary_scan_pads['gpio_0__gpio0__oe']['o']
 506     gpio1_oe = dut.jtag.boundary_scan_pads['gpio_0__gpio1__oe']['o']
 507     gpio2_oe = dut.jtag.boundary_scan_pads['gpio_0__gpio2__oe']['o']
 508     gpio3_oe = dut.jtag.boundary_scan_pads['gpio_0__gpio3__oe']['o']
 509     gpio_pad_oe = [gpio0_oe, gpio1_oe, gpio2_oe, gpio3_oe]
 510
 511     # Grab GPIO input pad resource from JTAG BS - start of chain
 512     gpio0_pad_in = dut.jtag.boundary_scan_pads['gpio_0__gpio0__i']['i']
 513     gpio1_pad_in = dut.jtag.boundary_scan_pads['gpio_0__gpio1__i']['i']
 514     gpio2_pad_in = dut.jtag.boundary_scan_pads['gpio_0__gpio2__i']['i']
 515     gpio3_pad_in = dut.jtag.boundary_scan_pads['gpio_0__gpio3__i']['i']
 516     gpio_pad_in = [gpio0_pad_in, gpio1_pad_in, gpio2_pad_in, gpio3_pad_in]
 517
 518     # Have the sim run through a for-loop where the gpio_o_test is
 519     # incremented like a counter (0000, 0001...)
 520     # At each iteration of the for-loop, assert:
 521     # + output set at core matches output seen at pad
 522     # TODO + input set at pad matches input seen at core
 523     # TODO + if gpio_o_test bit is cleared, output seen at pad matches
 524     # input seen at pad
 525     num_gpio_o_states = num_gpios**2
 526     pad_out = [0] * num_gpios
 527     pad_oe = [0] * num_gpios
 528     #print("Num of permutations of gpio_o_test record: ", num_gpio_o_states)
 529     for gpio_o_val in range(0, num_gpio_o_states):
 530         yield dut.gpio_o_test.eq(gpio_o_val)
 531         #yield Settle()
 532         yield # Move to the next clk cycle
 533
 534         # Cycle through all input combinations
 535         for gpio_i_val in range(0, num_gpio_o_states):
 536             # Set each gpio input at pad to test value
 537             for gpio_bit in range(0, num_gpios):
 538                 yield gpio_pad_in[gpio_bit].eq((gpio_i_val >> gpio_bit) & 0x1)
 539             yield
 540             # After changing the gpio0/1/2/3 inputs,
 541             # the output is also going to change.
 542             # *therefore it must be read again* to get the
 543             # snapshot (as a python value)
 544             for gpio_bit in range(0, num_gpios):
 545                 pad_out[gpio_bit] = yield gpio_pad_out[gpio_bit]
 546             yield
 547             for gpio_bit in range(0, num_gpios):
 548                 # check core and pad in
 549                 gpio_i_ro = yield dut.gpio_i_ro[gpio_bit]
 550                 out_test_bit = ((gpio_o_val & (1 << gpio_bit)) != 0)
 551                 in_bit = ((gpio_i_val & (1 << gpio_bit)) != 0)
 552                 # Check that the core end input matches pad
 553                 assert in_bit == gpio_i_ro
 554                 # Test that the output at pad matches:
 555                 # Pad output == given test output XOR test input
 556                 assert (out_test_bit ^ in_bit) == pad_out[gpio_bit]
 557
 558             # For debugging - VERY verbose
 559             #print("---------------------")
 560             #print("Test Out: ", bin(gpio_o_val))
 561             #print("Test Input: ", bin(gpio_i_val))
 562             # Print MSB first
 563             #print("Pad Output: ", list(reversed(pad_out)))
 564             #print("---------------------")
 565
 566     # For-loop for testing output enable signals
 567     for gpio_o_val in range(0, num_gpio_o_states):
 568         yield dut.gpio_oe_test.eq(gpio_o_val)
 569         yield # Move to the next clk cycle
 570
 571         for gpio_bit in range(0, num_gpios):
 572             pad_oe[gpio_bit] = yield gpio_pad_oe[gpio_bit]
 573         yield
 574
 575         for gpio_bit in range(0, num_gpios):
 576             oe_test_bit = ((gpio_o_val & (1 << gpio_bit)) != 0)
 577             # oe set at core matches oe seen at pad:
 578             assert oe_test_bit == pad_oe[gpio_bit]
 579         # For debugging - VERY verbose
 580         #print("---------------------")
 581         #print("Test Output Enable: ", bin(gpio_o_val))
 582         # Print MSB first
 583         #print("Pad Output Enable: ", list(reversed(pad_oe)))
 584         #print("---------------------")
 585
 586     # Reset test ouput register
 587     yield dut.gpio_o_test.eq(0)
 588     print("GPIO Test PASSED!")
 589
 590 def test_uart(dut):
 591     # grab the JTAG resource pad
 592     print ()
 593     print ("bs pad keys", dut.jtag.boundary_scan_pads.keys())
 594     print ()
 595     uart_rx_pad = dut.jtag.boundary_scan_pads['uart_0__rx']['i']
 596     uart_tx_pad = dut.jtag.boundary_scan_pads['uart_0__tx']['o']
 597
 598     print ("uart rx pad", uart_rx_pad)
 599     print ("uart tx pad", uart_tx_pad)
 600
 601     # Test UART by writing 0 and 1 to RX
 602     # Internally TX connected to RX,
 603     # so match pad TX with RX
 604     for i in range(0, 2):
 605         yield uart_rx_pad.eq(i)
 606         #yield uart_rx_pad.eq(i)
 607         yield Settle()
 608         yield # one clock cycle
 609         tx_val = yield uart_tx_pad
 610         print ("xmit uart", tx_val, 1)
 611         assert tx_val == i
 612
 613     print("UART Test PASSED!")
 614
 615 def test_i2c(dut):
 616     i2c_sda_i_pad = dut.jtag.boundary_scan_pads['i2c_0__sda__i']['i']
 617     i2c_sda_o_pad = dut.jtag.boundary_scan_pads['i2c_0__sda__o']['o']
 618     i2c_sda_oe_pad = dut.jtag.boundary_scan_pads['i2c_0__sda__oe']['o']
 619
 620     i2c_scl_i_pad = dut.jtag.boundary_scan_pads['i2c_0__scl__i']['i']
 621     i2c_scl_o_pad = dut.jtag.boundary_scan_pads['i2c_0__scl__o']['o']
 622     i2c_scl_oe_pad = dut.jtag.boundary_scan_pads['i2c_0__scl__oe']['o']
 623
 624     #i2c_pad = dut.jtag.resource_table_pads[('i2c', 0)]
 625     #print ("i2c pad", i2c_pad)
 626     #print ("i2c pad", i2c_pad.layout)
 627
 628     for i in range(0, 2):
 629         yield i2c_sda_i_pad.eq(i) #i2c_pad.sda.i.eq(i)
 630         yield i2c_scl_i_pad.eq(i) #i2c_pad.scl.i.eq(i)
 631         yield dut.i2c_sda_oe_test.eq(i)
 632         yield dut.i2c_scl_oe_test.eq(i)
 633         yield Settle()
 634         yield # one clock cycle
 635         sda_o_val = yield i2c_sda_o_pad
 636         scl_o_val = yield i2c_scl_o_pad
 637         sda_oe_val = yield i2c_sda_oe_pad
 638         scl_oe_val = yield i2c_scl_oe_pad
 639         print ("Test input: ", i, " SDA/SCL out: ", sda_o_val, scl_o_val,
 640                " SDA/SCL oe: ", sda_oe_val, scl_oe_val)
 641         assert sda_o_val == i
 642         assert scl_o_val == i
 643         assert sda_oe_val == i
 644         assert scl_oe_val == i
 645
 646     print("I2C Test PASSED!")
 647
 648 # JTAG boundary scan reg addresses - See c4m/nmigen/jtag/tap.py line #357
 649 BS_EXTEST = 0
 650 BS_INTEST = 0
 651 BS_SAMPLE = 2
 652 BS_PRELOAD = 2
 653 def test_jtag_bs_chain(dut):
 654     #print(dir(dut.jtag))
 655     #print(dir(dut))
 656     print("JTAG BS Reset")
 657     yield from jtag_set_reset(dut.jtag)
 658
 659     #print("JTAG I/O dictionary of core/pad signals:")
 660     #print(dut.jtag.ios.keys())
 661     # Based on number of ios entries, produce a test shift reg pattern - TODO
 662     bslen = len(dut.jtag.ios)
 663     bsdata = 2**bslen - 1 # Fill with all 1s for now
 664     empty_data = 0 # for testing
 665
 666     # TODO: make into a loop for future expansion
 667     # All pad input signals to drive and output via TDO
 668     i2c_sda_i_pad = dut.jtag.boundary_scan_pads['i2c_0__sda__i']['i']
 669     i2c_scl_i_pad = dut.jtag.boundary_scan_pads['i2c_0__scl__i']['i']
 670     uart_rx_pad = dut.jtag.boundary_scan_pads['uart_0__rx']['i']
 671     gpio0_pad_in = dut.jtag.boundary_scan_pads['gpio_0__gpio0__i']['i']
 672     gpio1_pad_in = dut.jtag.boundary_scan_pads['gpio_0__gpio1__i']['i']
 673     gpio2_pad_in = dut.jtag.boundary_scan_pads['gpio_0__gpio2__i']['i']
 674     gpio3_pad_in = dut.jtag.boundary_scan_pads['gpio_0__gpio3__i']['i']
 675
 676     # Assert all for now
 677     #yield i2c_sda_i_pad.eq(1)
 678     #yield i2c_scl_i_pad.eq(1)
 679     #yield uart_rx_pad.eq(1)
 680     #yield gpio0_pad_in.eq(1)
 681     #yield gpio1_pad_in.eq(1)
 682     #yield gpio2_pad_in.eq(1)
 683     #yield gpio3_pad_in.eq(1)
 684
 685     print("All pad inputs/core outputs reset, bs data all set")
 686     print("Sending TDI data with core/pads disconnected")
 687     result = yield from jtag_read_write_reg(dut.jtag, BS_EXTEST, bslen,
 688                                             bsdata)
 689     print("TDI BS Data: {0:b}, Data Length (bits): {1}"
 690           .format(bsdata, bslen))
 691     print("TDO BS Data: {0:b}".format(result))
 692
 693     print("Sending TDI data with core/pads connected")
 694     result = yield from jtag_read_write_reg(dut.jtag, BS_SAMPLE, bslen,
 695                                             bsdata)
 696     print("TDI BS Data: {0:b}, Data Length (bits): {1}"
 697           .format(bsdata, bslen))
 698     print("TDO BS Data: {0:b}".format(result))
 699
 700
 701     print("All pad inputs/core outputs set, bs data clear")
 702     bsdata = 0 # clear, as all input already asserted
 703     # Run through GPIO, UART, and I2C tests so that all signals are asserted
 704     yield from test_gpios(dut)
 705     yield from test_uart(dut)
 706     yield from test_i2c(dut)
 707
 708     print("Sending TDI data with core/pads disconnected")
 709     result = yield from jtag_read_write_reg(dut.jtag, BS_EXTEST, bslen,
 710                                             bsdata)
 711     print("TDI BS Data: {0:b}, Data Length (bits): {1}"
 712           .format(bsdata, bslen))
 713     print("TDO BS Data: {0:b}".format(result))
 714
 715     print("Sending TDI data with core/pads connected")
 716     result = yield from jtag_read_write_reg(dut.jtag, BS_SAMPLE, bslen,
 717                                             bsdata)
 718     print("TDI BS Data: {0:b}, Data Length (bits): {1}"
 719           .format(bsdata, bslen))
 720     print("TDO BS Data: {0:b}".format(result))
 721
 722
 723     # Implement a decode which uses ios keys to determine if correct bits in
 724     # the TDO stream are set (using asserts) - TODO
 725     print("Starting test with ios keys")
 726     ios_keys = list(dut.jtag.ios.keys())
 727     for i in range(0, bslen):
 728         # Check if outputs are asserted
 729         if ('__o' in ios_keys[i]) or ('__tx' in ios_keys[i]):
 730             signal = ios_keys[i]
 731             print("Output | Name: ", signal)
 732             temp_result = yield dut.jtag.boundary_scan_pads[signal]['o']
 733             print(signal, " : ", temp_result)
 734             assert temp_result == 1
 735         else:
 736             signal = ios_keys[i]
 737             print("Input | Name: ", signal)
 738
 739     print("JTAG Boundary Scan Chain Test PASSED!")
 740
 741 # Copied from test_jtag_tap.py
 742 # JTAG-ircodes for accessing DMI
 743 DMI_ADDR = 5
 744 DMI_READ = 6
 745 DMI_WRRD = 7
 746
 747 # JTAG-ircodes for accessing Wishbone
 748 WB_ADDR = 8
 749 WB_READ = 9
 750 WB_WRRD = 10
 751
 752 def test_jtag_dmi_wb():
 753     print(dir(top.jtag))
 754     print(dir(top))
 755     print("JTAG BS Reset")
 756     yield from jtag_set_reset(top.jtag)
 757
 758     print("JTAG I/O dictionary of core/pad signals:")
 759     print(top.jtag.ios.keys())
 760
 761     # Copied from test_jtag_tap
 762     # Don't know if the ID is the same for all JTAG instances
 763     ####### JTAGy stuff (IDCODE) ######
 764
 765     # read idcode
 766     idcode = yield from jtag_read_write_reg(top.jtag, 0b1, 32)
 767     print ("idcode", hex(idcode))
 768     assert idcode == 0x18ff
 769
 770     ####### JTAG to DMI ######
 771
 772     # write DMI address
 773     yield from jtag_read_write_reg(top.jtag, DMI_ADDR, 8, DBGCore.CTRL)
 774
 775     # read DMI CTRL register
 776     status = yield from jtag_read_write_reg(top.jtag, DMI_READ, 64)
 777     print ("dmi ctrl status", hex(status))
 778     #assert status == 4
 779
 780     # write DMI address
 781     yield from jtag_read_write_reg(top.jtag, DMI_ADDR, 8, 0)
 782
 783     # write DMI CTRL register
 784     status = yield from jtag_read_write_reg(top.jtag, DMI_WRRD, 64, 0b101)
 785     print ("dmi ctrl status", hex(status))
 786     #assert status == 4 # returned old value (nice! cool feature!)
 787
 788     # write DMI address
 789     yield from jtag_read_write_reg(top.jtag, DMI_ADDR, 8, DBGCore.CTRL)
 790
 791     # read DMI CTRL register
 792     status = yield from jtag_read_write_reg(top.jtag, DMI_READ, 64)
 793     print ("dmi ctrl status", hex(status))
 794     #assert status == 6
 795
 796     # write DMI MSR address
 797     yield from jtag_read_write_reg(top.jtag, DMI_ADDR, 8, DBGCore.MSR)
 798
 799     # read DMI MSR register
 800     msr = yield from jtag_read_write_reg(top.jtag, DMI_READ, 64)
 801     print ("dmi msr", hex(msr))
 802     #assert msr == 0xdeadbeef
 803
 804     ####### JTAG to Wishbone ######
 805
 806     # write Wishbone address
 807     yield from jtag_read_write_reg(top.jtag, WB_ADDR, 16, 0x18)
 808
 809     # write/read wishbone data
 810     data = yield from jtag_read_write_reg(top.jtag, WB_WRRD, 16, 0xfeef)
 811     print ("wb write", hex(data))
 812
 813     # write Wishbone address
 814     yield from jtag_read_write_reg(top.jtag, WB_ADDR, 16, 0x18)
 815
 816     # write/read wishbone data
 817     data = yield from jtag_read_write_reg(top.jtag, WB_READ, 16, 0)
 818     print ("wb read", hex(data))
 819
 820     ####### done - tell dmi_sim to stop (otherwise it won't) ########
 821
 822     top.jtag.stop = True
 823
 824 def test_debug_print(dut):
 825     print("Test used for getting object methods/information")
 826     print("Moved here to clear clutter of gpio test")
 827
 828     print ("printing out info about the resource gpio0")
 829     print (dut.gpio['gpio0']['i'])
 830     print ("this is a PIN resource", type(dut.gpio['gpio0']['i']))
 831     # yield can only be done on SIGNALS or RECORDS,
 832     # NOT Pins/Resources gpio0_core_in = yield top.gpio['gpio0']['i']
 833     #print("Test gpio0 core in: ", gpio0_core_in)
 834
 835     print("JTAG")
 836     print(dut.jtag.__class__.__name__, dir(dut.jtag))
 837     print("TOP")
 838     print(dut.__class__.__name__, dir(dut))
 839     print("PORT")
 840     print(dut.ports.__class__.__name__, dir(dut.ports))
 841     print("GPIO")
 842     print(dut.gpio.__class__.__name__, dir(dut.gpio))
 843
 844     print("UART")
 845     print(dir(dut.jtag.boundary_scan_pads['uart_0__rx__pad__i']))
 846     print(dut.jtag.boundary_scan_pads['uart_0__rx__pad__i'].keys())
 847     print(dut.jtag.boundary_scan_pads['uart_0__tx__pad__o'])
 848     #print(type(dut.jtag.boundary_scan_pads['uart_0__rx__pad__i']['rx']))
 849     print ("jtag pad table keys")
 850     print (dut.jtag.resource_table_pads.keys())
 851     print(type(dut.jtag.resource_table_pads[('uart', 0)].rx.i))
 852     print(dut.jtag.boundary_scan_pads['uart_0__rx__i'])
 853
 854     print("I2C")
 855     print(dut.jtag.boundary_scan_pads['i2c_0__sda__i'])
 856     print(type(dut.jtag.boundary_scan_pads['i2c_0__sda__i']['i']))
 857
 858     print(dut.jtag.resource_table_pads)
 859     print(dut.jtag.boundary_scan_pads)
 860
 861
 862     # Trying to read input from core side, looks like might be a pin...
 863     # XXX don't "look like" - don't guess - *print it out*
 864     #print ("don't guess, CHECK", type(top.gpio.gpio0.i))
 865
 866     print () # extra print to divide the output
 867     yield
 868
 869 def setup_blinker(build_blinker=False):
 870     """
 871     and to create a Platform instance with that list, and build
 872     something random
 873
 874        p=Platform()
 875        p.resources=listofstuff
 876        p.build(Blinker())
 877     """
 878
 879     pinset = dummy_pinset()
 880     print(pinset)
 881     resources = create_resources(pinset)
 882     top = Blinker(pinset, resources, no_jtag_connect=False)#True)
 883
 884     vl = rtlil.convert(top, ports=top.ports())
 885     with open("test_jtag_blinker.il", "w") as f:
 886         f.write(vl)
 887
 888     if build_blinker:
 889         # XXX these modules are all being added *AFTER* the build process links
 890         # everything together.  the expectation that this would work is...
 891         # unrealistic.  ordering, clearly, is important.
 892
 893         # This JTAG code copied from test, probably not needed
 894         # dut = JTAG(test_pinset(), wb_data_wid=64, domain="sync")
 895         top.jtag.stop = False
 896         # rather than the client access the JTAG bus directly
 897         # create an alternative that the client sets
 898         class Dummy: pass
 899         cdut = Dummy()
 900         cdut.cbus = JTAGInterface()
 901
 902         # set up client-server on port 44843-something
 903         top.jtag.s = JTAGServer()
 904         cdut.c = JTAGClient()
 905         top.jtag.s.get_connection()
 906         #else:
 907         #    print ("running server only as requested,
 908         #           use openocd remote to test")
 909         #    sys.stdout.flush()
 910         #    top.jtag.s.get_connection(None) # block waiting for connection
 911
 912         # take copy of ir_width and scan_len
 913         cdut._ir_width = top.jtag._ir_width
 914         cdut.scan_len = top.jtag.scan_len
 915
 916         p = ASICPlatform (resources, top.jtag)
 917         p.build(top)
 918         # this is what needs to gets treated as "top", after "main module" top
 919         # is augmented with IO pads with JTAG tacked on.  the expectation that
 920         # the get_input() etc functions will be called magically by some other
 921         # function is unrealistic.
 922         top_fragment = p.fragment
 923
 924     return top
 925
 926 def test_jtag():
 927     dut = setup_blinker(build_blinker=False)
 928
 929     # XXX simulating top (the module that does not itself contain IO pads
 930     # because that's covered by build) cannot possibly be expected to work
 931     # particularly when modules have been added *after* the platform build()
 932     # function has been called.
 933
 934     sim = Simulator(dut)
 935     sim.add_clock(1e-6, domain="sync")      # standard clock
 936
 937     #sim.add_sync_process(wrap(jtag_srv(top))) #? jtag server
 938     #if len(sys.argv) != 2 or sys.argv[1] != 'server':
 939     # actual jtag tester
 940     #sim.add_sync_process(wrap(jtag_sim(cdut, top.jtag)))
 941     # handles (pretends to be) DMI
 942     #sim.add_sync_process(wrap(dmi_sim(top.jtag)))
 943
 944     #sim.add_sync_process(wrap(test_gpios(top)))
 945     #sim.add_sync_process(wrap(test_uart(top)))
 946     #sim.add_sync_process(wrap(test_i2c(top)))
 947     #sim.add_sync_process(wrap(test_debug_print()))
 948
 949     sim.add_sync_process(wrap(test_jtag_bs_chain(dut)))
 950
 951     with sim.write_vcd("blinker_test.vcd"):
 952         sim.run()
 953
 954 if __name__ == '__main__':
 955     test_jtag()