import unittest
-from nmigen import Elaboratable, Module, Memory, Signal
+from nmigen import Elaboratable, Module, Memory, Signal, Repl, Mux
from nmigen.back import rtlil
from nmigen.sim import Simulator
from nmigen.asserts import Assert, Assume, Past, AnyConst
self.addr_width = addr_width
self.data_width = data_width
self.we_width = we_width
- self.d = Signal(data_width)
- """ write data"""
- self.q = Signal(data_width)
- """read data"""
- self.a = Signal(addr_width)
- """ read/write address"""
- self.we = Signal(we_width)
- """write enable"""
- self.dbg_a = Signal(addr_width)
- """debug read port address"""
- self.dbg_q = Signal(data_width)
- """debug read port data"""
-
- def elaborate(self, _):
+ # interface signals
+ self.d = Signal(data_width); """ write data"""
+ self.q = Signal(data_width); """read data"""
+ self.a = Signal(addr_width); """ read/write address"""
+ self.we = Signal(we_width); """write enable"""
+ # debug signals, only used in formal proofs
+ self.dbg_addr = Signal(addr_width); """debug: address under test"""
+ lanes = range(we_width)
+ self.dbg_lane = Signal(lanes); """debug: write lane under test"""
+ gran = self.data_width // self.we_width
+ self.dbg_data = Signal(gran); """debug: data to keep in sync"""
+ self.dbg_wrote = Signal(); """debug: data is valid"""
+
+ def elaborate(self, platform):
m = Module()
# backing memory
depth = 1 << self.addr_width
- granularity = self.data_width // self.we_width
+ gran = self.data_width // self.we_width
mem = Memory(width=self.data_width, depth=depth)
# create read and write ports
# By connecting the same address to both ports, they behave, in fact,
# Note that nmigen memories have a one cycle delay, for reads,
# by default
m.submodules.rdport = rdport = mem.read_port(transparent=True)
- m.submodules.wrport = wrport = mem.write_port(granularity=granularity)
+ m.submodules.wrport = wrport = mem.write_port(granularity=gran)
# duplicate the address to both ports
m.d.comb += wrport.addr.eq(self.a)
m.d.comb += rdport.addr.eq(self.a)
# read and write data
m.d.comb += wrport.data.eq(self.d)
m.d.comb += self.q.eq(rdport.data)
- # the debug port is an asynchronous read port, allowing direct access
- # to a given memory location by the formal engine
- m.submodules.dbgport = dbgport = mem.read_port(domain="comb")
- m.d.comb += dbgport.addr.eq(self.dbg_a)
- m.d.comb += self.dbg_q.eq(dbgport.data)
+
+ # the following is needed for induction, where an unreachable state
+ # (memory and holding register differ) is turned into an illegal one
+ if platform == "formal":
+ # the debug port is an asynchronous read port, allowing direct
+ # access to a given memory location by the formal engine
+ m.submodules.dbgport = dbgport = mem.read_port(domain="comb")
+ # first, get the value stored in our memory location,
+ # using its debug port
+ stored = Signal(self.data_width)
+ m.d.comb += dbgport.addr.eq(self.dbg_addr)
+ m.d.comb += stored.eq(dbgport.data)
+ # now, ensure that the value stored in memory is always in sync
+ # with the holding register
+ with m.If(self.dbg_wrote):
+ m.d.sync += Assert(self.dbg_data ==
+ stored.word_select(self.dbg_lane, gran))
+
return m
def ports(self):
gran = len(dut.d) // len(dut.we) # granularity
# choose a single random memory location to test
a_const = AnyConst(dut.a.shape())
- # choose a single byte lane to test (one-hot encoding)
- we_mask = Signal.like(dut.we)
- # ... by first creating a random bit pattern
- we_const = AnyConst(dut.we.shape())
- # ... and zeroing all but the first non-zero bit
- m.d.comb += we_mask.eq(we_const & (-we_const))
+ # choose a single byte lane to test
+ lane = AnyConst(range(dut.we_width))
# holding data register
d_reg = Signal(gran)
# for some reason, simulated formal memory is not zeroed at reset
wrote = Signal()
# if our memory location and byte lane is being written
# ... capture the data in our holding register
- with m.If(dut.a == a_const):
- for i in range(len(dut.we)):
- with m.If(we_mask[i] & dut.we[i]):
- m.d.sync += d_reg.eq(dut.d[i*gran:i*gran+gran])
- m.d.sync += wrote.eq(1)
+ with m.If((dut.a == a_const) & dut.we.bit_select(lane, 1)):
+ m.d.sync += d_reg.eq(dut.d.word_select(lane, gran))
+ m.d.sync += wrote.eq(1)
# if our memory location is being read
# ... and the holding register has valid data
# ... then its value must match the memory output, on the given lane
with m.If((Past(dut.a) == a_const) & wrote):
- for i in range(len(dut.we)):
- with m.If(we_mask[i]):
- m.d.sync += Assert(d_reg == dut.q[i*gran:i*gran+gran])
-
- # the following is needed for induction, where an unreachable state
- # (memory and holding register differ) is turned into an illegal one
- # first, get the value stored in our memory location, using its debug
- # port
- stored = Signal.like(dut.q)
- m.d.comb += dut.dbg_a.eq(a_const)
- m.d.comb += stored.eq(dut.dbg_q)
- # now, ensure that the value stored in memory is always in sync
- # with the holding register
- with m.If(wrote):
- for i in range(len(dut.we)):
- with m.If(we_mask[i]):
- m.d.sync += Assert(d_reg == stored[i*gran:i*gran+gran])
+ m.d.sync += Assert(d_reg == dut.q.word_select(lane, gran))
+
+ # pass our state to the device under test, so it can ensure that
+ # its state is in sync with ours, for induction
+ m.d.comb += [
+ dut.dbg_addr.eq(a_const),
+ dut.dbg_lane.eq(lane),
+ dut.dbg_data.eq(d_reg),
+ dut.dbg_wrote.eq(wrote),
+ ]
self.assertFormal(m, mode="prove", depth=2)
self.we_width = we_width
self.write_phase = write_phase
self.transparent = transparent
- self.wr_addr_i = Signal(addr_width)
- """write port address"""
- self.wr_data_i = Signal(data_width)
- """write port data"""
- self.wr_we_i = Signal(we_width)
- """write port enable"""
- self.rd_addr_i = Signal(addr_width)
- """read port address"""
- self.rd_data_o = Signal(data_width)
- """read port data"""
- self.phase = Signal()
- """even/odd cycle indicator"""
- self.dbg_a = Signal(addr_width)
- """debug read port address"""
- self.dbg_q1 = Signal(data_width)
- """debug read port data (first memory)"""
- self.dbg_q2 = Signal(data_width)
- """debug read port data (second memory)"""
-
- def elaborate(self, _):
+ # interface signals
+ self.wr_addr_i = Signal(addr_width); """write port address"""
+ self.wr_data_i = Signal(data_width); """write port data"""
+ self.wr_we_i = Signal(we_width); """write port enable"""
+ self.rd_addr_i = Signal(addr_width); """read port address"""
+ self.rd_data_o = Signal(data_width); """read port data"""
+ self.phase = Signal(); """even/odd cycle indicator"""
+ # debug signals, only used in formal proofs
+ self.dbg_addr = Signal(addr_width); """debug: address under test"""
+ lanes = range(we_width)
+ self.dbg_lane = Signal(lanes); """debug: write lane under test"""
+ gran = self.data_width // self.we_width
+ self.dbg_data = Signal(gran); """debug: data to keep in sync"""
+ self.dbg_wrote = Signal(); """debug: data is valid"""
+
+ def elaborate(self, platform):
m = Module()
+ # granularity
# instantiate the two 1RW memory blocks
mem1 = SinglePortSRAM(self.addr_width, self.data_width, self.we_width)
mem2 = SinglePortSRAM(self.addr_width, self.data_width, self.we_width)
# always output the read data from the second memory,
# if not transparent
m.d.comb += self.rd_data_o.eq(mem2.q)
- # our debug port allow the formal engine to inspect the content of
- # a fixed, arbitrary address, on our memory blocks.
- # wire it to their debug ports.
- m.d.comb += mem1.dbg_a.eq(self.dbg_a)
- m.d.comb += mem2.dbg_a.eq(self.dbg_a)
- m.d.comb += self.dbg_q1.eq(mem1.dbg_q)
- m.d.comb += self.dbg_q2.eq(mem2.dbg_q)
+
+ if platform == "formal":
+ # pass our state to the device under test, so it can ensure that
+ # its state is in sync with ours, for induction
+ m.d.comb += [
+ # pass the address and write lane under test to both memories
+ mem1.dbg_addr.eq(self.dbg_addr),
+ mem2.dbg_addr.eq(self.dbg_addr),
+ mem1.dbg_lane.eq(self.dbg_lane),
+ mem2.dbg_lane.eq(self.dbg_lane),
+ # the second memory copies its state from the first memory,
+ # after a cycle, so it has a one cycle delay
+ mem1.dbg_data.eq(self.dbg_data),
+ mem2.dbg_data.eq(Past(self.dbg_data)),
+ mem1.dbg_wrote.eq(self.dbg_wrote),
+ mem2.dbg_wrote.eq(Past(self.dbg_wrote)),
+ ]
return m
with self.subTest("writes happen on phase 1 (transparent reads)"):
self.do_test_phased_dual_port_regfile(1, True)
- def do_test_phased_dual_port_regfile_proof(self, write_phase):
+ def do_test_phased_dual_port_regfile_proof(self, write_phase, transparent):
"""
Formal proof of the pseudo 1W/1R regfile
"""
m = Module()
# 128 x 32-bit, 8-bit granularity
- dut = PhasedDualPortRegfile(7, 32, 4, write_phase, True)
+ dut = PhasedDualPortRegfile(7, 32, 4, write_phase, transparent)
m.submodules.dut = dut
gran = dut.data_width // dut.we_width # granularity
# choose a single random memory location to test
a_const = AnyConst(dut.addr_width)
- # choose a single byte lane to test (one-hot encoding)
- we_mask = Signal(dut.we_width)
- # ... by first creating a random bit pattern
- we_const = AnyConst(dut.we_width)
- # ... and zeroing all but the first non-zero bit
- m.d.comb += we_mask.eq(we_const & (-we_const))
+ # choose a single byte lane to test
+ lane = AnyConst(range(dut.we_width))
# drive alternating phases
m.d.comb += Assume(dut.phase != Past(dut.phase))
# holding data register
# if our memory location and byte lane is being written,
# capture the data in our holding register
with m.If((dut.wr_addr_i == a_const)
+ & dut.wr_we_i.bit_select(lane, 1)
& (dut.phase == dut.write_phase)):
- for i in range(dut.we_width):
- with m.If(we_mask[i] & dut.wr_we_i[i]):
- m.d.sync += d_reg.eq(
- dut.wr_data_i[i * gran:i * gran + gran])
- m.d.sync += wrote.eq(1)
+ m.d.sync += d_reg.eq(dut.wr_data_i.word_select(lane, gran))
+ m.d.sync += wrote.eq(1)
# if our memory location is being read,
# and the holding register has valid data,
# then its value must match the memory output, on the given lane
- with m.If((Past(dut.rd_addr_i) == a_const) & wrote):
- for i in range(dut.we_width):
- with m.If(we_mask[i]):
- m.d.sync += Assert(
- d_reg == dut.rd_data_o[i * gran:i * gran + gran])
-
- # the following is needed for induction, where an unreachable state
- # (memory and holding register differ) is turned into an illegal one
- # first, get the values stored in our memory location, using its
- # debug port
- stored1 = Signal(dut.data_width)
- stored2 = Signal(dut.data_width)
- m.d.comb += dut.dbg_a.eq(a_const)
- m.d.comb += stored1.eq(dut.dbg_q1)
- m.d.comb += stored2.eq(dut.dbg_q2)
- # now, ensure that the value stored in the first memory is always
- # in sync with the holding register
- with m.If(wrote):
- for i in range(dut.we_width):
- with m.If(we_mask[i]):
- m.d.comb += Assert(
- d_reg == stored1[i * gran:i * gran + gran])
- # same for the second memory, but one cycle later
- with m.If(Past(wrote)):
- for i in range(dut.we_width):
- with m.If(we_mask[i]):
- m.d.comb += Assert(
- Past(d_reg) == stored2[i * gran:i * gran + gran])
+ with m.If(Past(dut.rd_addr_i) == a_const):
+ if transparent:
+ with m.If(wrote):
+ rd_lane = dut.rd_data_o.word_select(lane, gran)
+ m.d.sync += Assert(d_reg == rd_lane)
+ else:
+ # with a non-transparent read port, the read value depends
+ # on whether there is a simultaneous write, or not
+ with m.If((Past(dut.wr_addr_i) == a_const)
+ & Past(dut.phase) == dut.write_phase):
+ # simultaneous write -> check against last written value
+ with m.If(Past(wrote)):
+ rd_lane = dut.rd_data_o.word_select(lane, gran)
+ m.d.sync += Assert(Past(d_reg) == rd_lane)
+ with m.Else():
+ # otherwise, check against current written value
+ with m.If(wrote):
+ rd_lane = dut.rd_data_o.word_select(lane, gran)
+ m.d.sync += Assert(d_reg == rd_lane)
+
+ # pass our state to the device under test, so it can ensure that
+ # its state is in sync with ours, for induction
+ m.d.comb += [
+ # address and mask under test
+ dut.dbg_addr.eq(a_const),
+ dut.dbg_lane.eq(lane),
+ # state of our holding register
+ dut.dbg_data.eq(d_reg),
+ dut.dbg_wrote.eq(wrote),
+ ]
- self.assertFormal(m, mode="prove", depth=2)
+ self.assertFormal(m, mode="prove", depth=3)
def test_phased_dual_port_regfile_proof(self):
"""test both types (odd and even write ports) of phased write memory"""
with self.subTest("writes happen on phase 0"):
- self.do_test_phased_dual_port_regfile_proof(0)
+ self.do_test_phased_dual_port_regfile_proof(0, False)
with self.subTest("writes happen on phase 1"):
- self.do_test_phased_dual_port_regfile_proof(1)
+ self.do_test_phased_dual_port_regfile_proof(1, False)
+ # test again, with transparent read ports
+ with self.subTest("writes happen on phase 0 (transparent reads)"):
+ self.do_test_phased_dual_port_regfile_proof(0, True)
+ with self.subTest("writes happen on phase 1 (transparent reads)"):
+ self.do_test_phased_dual_port_regfile_proof(1, True)
+
+
+class DualPortRegfile(Elaboratable):
+ """
+ Builds, from a pair of phased 1W/1R blocks, a true 1W/1R RAM, where both
+ read and write ports work every cycle.
+ It employs a Last Value Table, that tracks to which memory each address was
+ last written.
+
+ :param addr_width: width of the address bus
+ :param data_width: width of the data bus
+ :param we_width: number of write enable lines
+ :param transparent: whether a simultaneous read and write returns the
+ new value (True) or the old value (False)
+ """
+
+ def __init__(self, addr_width, data_width, we_width, transparent=True):
+ self.addr_width = addr_width
+ self.data_width = data_width
+ self.we_width = we_width
+ self.transparent = transparent
+ # interface signals
+ self.wr_addr_i = Signal(addr_width); """write port address"""
+ self.wr_data_i = Signal(data_width); """write port data"""
+ self.wr_we_i = Signal(we_width); """write port enable"""
+ self.rd_addr_i = Signal(addr_width); """read port address"""
+ self.rd_data_o = Signal(data_width); """read port data"""
+ # debug signals, only used in formal proofs
+ # address and write lane under test
+ self.dbg_addr = Signal(addr_width); """debug: address under test"""
+ lanes = range(we_width)
+ self.dbg_lane = Signal(lanes); """debug: write lane under test"""
+ # upstream state, to keep in sync with ours
+ gran = self.data_width // self.we_width
+ self.dbg_data = Signal(gran); """debug: data to keep in sync"""
+ self.dbg_wrote = Signal(); """debug: data is valid"""
+ self.dbg_wrote_phase = Signal(); """debug: the phase data was written"""
+ self.dbg_phase = Signal(); """debug: current phase"""
+
+ def elaborate(self, platform):
+ m = Module()
+ # depth and granularity
+ depth = 1 << self.addr_width
+ gran = self.data_width // self.we_width
+ # instantiate the two phased 1R/1W memory blocks
+ mem0 = PhasedDualPortRegfile(
+ self.addr_width, self.data_width, self.we_width, 0,
+ self.transparent)
+ mem1 = PhasedDualPortRegfile(
+ self.addr_width, self.data_width, self.we_width, 1,
+ self.transparent)
+ m.submodules.mem0 = mem0
+ m.submodules.mem1 = mem1
+ # instantiate the backing memory (FFRAM or LUTRAM)
+ # for the Last Value Table
+ # it should have the same number and port types of the desired
+ # memory, but just one bit per write lane
+ lvt_mem = Memory(width=self.we_width, depth=depth)
+ lvt_wr = lvt_mem.write_port(granularity=1)
+ lvt_rd = lvt_mem.read_port(transparent=self.transparent)
+ m.submodules.lvt_wr = lvt_wr
+ m.submodules.lvt_rd = lvt_rd
+ # generate and wire the phases for the phased memories
+ phase = Signal()
+ m.d.sync += phase.eq(~phase)
+ m.d.comb += [
+ mem0.phase.eq(phase),
+ mem1.phase.eq(phase),
+ ]
+ m.d.comb += [
+ # wire the write ports, directly
+ mem0.wr_addr_i.eq(self.wr_addr_i),
+ mem1.wr_addr_i.eq(self.wr_addr_i),
+ mem0.wr_we_i.eq(self.wr_we_i),
+ mem1.wr_we_i.eq(self.wr_we_i),
+ mem0.wr_data_i.eq(self.wr_data_i),
+ mem1.wr_data_i.eq(self.wr_data_i),
+ # also wire the read addresses
+ mem0.rd_addr_i.eq(self.rd_addr_i),
+ mem1.rd_addr_i.eq(self.rd_addr_i),
+ # wire read and write ports to the LVT
+ lvt_wr.addr.eq(self.wr_addr_i),
+ lvt_wr.en.eq(self.wr_we_i),
+ lvt_rd.addr.eq(self.rd_addr_i),
+ # the data for the LVT is the phase on which the value was
+ # written
+ lvt_wr.data.eq(Repl(phase, self.we_width)),
+ ]
+ for i in range(self.we_width):
+ # select the right memory to assign to the output read port,
+ # in this byte lane, according to the LVT contents
+ m.d.comb += self.rd_data_o.word_select(i, gran).eq(
+ Mux(
+ lvt_rd.data[i],
+ mem1.rd_data_o.word_select(i, gran),
+ mem0.rd_data_o.word_select(i, gran)))
+
+ if platform == "formal":
+ # pass upstream state to the memories, so they can ensure that
+ # their state are in sync with upstream, for induction
+ m.d.comb += [
+ # address and write lane under test
+ mem0.dbg_addr.eq(self.dbg_addr),
+ mem1.dbg_addr.eq(self.dbg_addr),
+ mem0.dbg_lane.eq(self.dbg_lane),
+ mem1.dbg_lane.eq(self.dbg_lane),
+ # upstream state
+ mem0.dbg_data.eq(self.dbg_data),
+ mem1.dbg_data.eq(self.dbg_data),
+ # the memory, on which the write ends up, depends on which
+ # phase it was written
+ mem0.dbg_wrote.eq(self.dbg_wrote & ~self.dbg_wrote_phase),
+ mem1.dbg_wrote.eq(self.dbg_wrote & self.dbg_wrote_phase),
+ ]
+ # sync phase to upstream
+ m.d.comb += Assert(self.dbg_phase == phase)
+ # this debug port for the LVT is an asynchronous read port,
+ # allowing direct access to a given memory location
+ # by the formal engine
+ m.submodules.dbgport = dbgport = lvt_mem.read_port(domain='comb')
+ # first, get the value stored in our memory location,
+ stored = Signal(self.we_width)
+ m.d.comb += dbgport.addr.eq(self.dbg_addr)
+ m.d.comb += stored.eq(dbgport.data)
+ # now, ensure that the value stored in memory is always in sync
+ # with the expected value (which memory the value was written to)
+ with m.If(self.dbg_wrote):
+ m.d.comb += Assert(stored.bit_select(self.dbg_lane, 1)
+ == self.dbg_wrote_phase)
+ return m
+
+
+class DualPortRegfileTestCase(FHDLTestCase):
+
+ def do_test_dual_port_regfile(self, transparent):
+ """
+ Simulate some read/write/modify operations on the dual port register
+ file
+ """
+ dut = DualPortRegfile(7, 32, 4, transparent)
+ sim = Simulator(dut)
+ sim.add_clock(1e-6)
+
+ expected = None
+ last_expected = None
+
+ # compare read data with previously written data
+ # and start a new read
+ def read(rd_addr_i, next_expected=None):
+ nonlocal expected, last_expected
+ if expected is not None:
+ self.assertEqual((yield dut.rd_data_o), expected)
+ yield dut.rd_addr_i.eq(rd_addr_i)
+ # account for the read latency
+ expected = last_expected
+ last_expected = next_expected
+
+ # start a write
+ def write(wr_addr_i, wr_we_i, wr_data_i):
+ yield dut.wr_addr_i.eq(wr_addr_i)
+ yield dut.wr_we_i.eq(wr_we_i)
+ yield dut.wr_data_i.eq(wr_data_i)
+
+ def process():
+ # write a pair of values, one for each memory
+ yield from read(0)
+ yield from write(0x42, 0b1111, 0x87654321)
+ yield
+ yield from read(0x42, 0x87654321)
+ yield from write(0x43, 0b1111, 0x0FEDCBA9)
+ yield
+ # skip a beat
+ yield from read(0x43, 0x0FEDCBA9)
+ yield from write(0, 0, 0)
+ yield
+ # write again, but now they switch memories
+ yield from read(0)
+ yield from write(0x42, 0b1111, 0x12345678)
+ yield
+ yield from read(0x42, 0x12345678)
+ yield from write(0x43, 0b1111, 0x9ABCDEF0)
+ yield
+ yield from read(0x43, 0x9ABCDEF0)
+ yield from write(0, 0, 0)
+ yield
+ # test partial writes
+ yield from read(0)
+ yield from write(0x42, 0b1001, 0x78FFFF12)
+ yield
+ yield from read(0)
+ yield from write(0x43, 0b0110, 0xFFDEABFF)
+ yield
+ yield from read(0x42, 0x78345612)
+ yield from write(0, 0, 0)
+ yield
+ yield from read(0x43, 0x9ADEABF0)
+ yield from write(0, 0, 0)
+ yield
+ yield from read(0)
+ yield from write(0, 0, 0)
+ yield
+ if transparent:
+ # returns the value just written
+ yield from read(0x42, 0x55AA9966)
+ else:
+ # returns the old value
+ yield from read(0x42, 0x78345612)
+ yield from write(0x42, 0b1111, 0x55AA9966)
+ yield
+ # after a cycle, always returns the new value
+ yield from read(0x42, 0x55AA9966)
+ yield from write(0, 0, 0)
+ yield
+ yield from read(0)
+ yield from write(0, 0, 0)
+ yield
+ yield from read(0)
+ yield from write(0, 0, 0)
+
+ sim.add_sync_process(process)
+ debug_file = 'test_dual_port_regfile'
+ if transparent:
+ debug_file += '_transparent'
+ traces = ['clk', 'phase',
+ {'comment': 'write port'},
+ 'wr_addr_i[6:0]', 'wr_we_i[3:0]', 'wr_data_i[31:0]',
+ {'comment': 'read port'},
+ 'rd_addr_i[6:0]', 'rd_data_o[31:0]',
+ {'comment': 'LVT write port'},
+ 'phase', 'lvt_mem_w_addr[6:0]', 'lvt_mem_w_en[3:0]',
+ 'lvt_mem_w_data[3:0]',
+ {'comment': 'LVT read port'},
+ 'lvt_mem_r_addr[6:0]', 'lvt_mem_r_data[3:0]',
+ {'comment': 'backing memory'},
+ 'mem0.rd_data_o[31:0]',
+ 'mem1.rd_data_o[31:0]',
+ ]
+ write_gtkw(debug_file + '.gtkw',
+ debug_file + '.vcd',
+ traces, module='top', zoom=-22)
+ sim_writer = sim.write_vcd(debug_file + '.vcd')
+ with sim_writer:
+ sim.run()
+
+ def test_dual_port_regfile(self):
+ with self.subTest("non-transparent reads"):
+ self.do_test_dual_port_regfile(False)
+ with self.subTest("transparent reads"):
+ self.do_test_dual_port_regfile(True)
+
+ def test_dual_port_regfile_proof(self):
+ """
+ Formal proof of the 1W/1R regfile
+ """
+ m = Module()
+ # 128 x 32-bit, 8-bit granularity
+ dut = DualPortRegfile(7, 32, 4, True)
+ m.submodules.dut = dut
+ gran = dut.data_width // dut.we_width # granularity
+ # choose a single random memory location to test
+ a_const = AnyConst(dut.addr_width)
+ # choose a single byte lane to test
+ lane = AnyConst(range(dut.we_width))
+ # holding data register
+ d_reg = Signal(gran)
+ # keep track of the phase, so we can remember which memory
+ # we wrote to
+ phase = Signal()
+ m.d.sync += phase.eq(~phase)
+ # for some reason, simulated formal memory is not zeroed at reset
+ # ... so, remember whether we wrote it, at least once.
+ wrote = Signal()
+ # ... and on which phase it was written
+ wrote_phase = Signal()
+ # if our memory location and byte lane is being written,
+ # capture the data in our holding register
+ with m.If((dut.wr_addr_i == a_const)
+ & dut.wr_we_i.bit_select(lane, 1)):
+ m.d.sync += d_reg.eq(dut.wr_data_i.word_select(lane, gran))
+ m.d.sync += wrote.eq(1)
+ m.d.sync += wrote_phase.eq(phase)
+ # if our memory location is being read,
+ # and the holding register has valid data,
+ # then its value must match the memory output, on the given lane
+ with m.If(Past(dut.rd_addr_i) == a_const):
+ with m.If(wrote):
+ rd_lane = dut.rd_data_o.word_select(lane, gran)
+ m.d.sync += Assert(d_reg == rd_lane)
+
+ m.d.comb += [
+ dut.dbg_addr.eq(a_const),
+ dut.dbg_lane.eq(lane),
+ dut.dbg_data.eq(d_reg),
+ dut.dbg_wrote.eq(wrote),
+ dut.dbg_wrote_phase.eq(wrote_phase),
+ dut.dbg_phase.eq(phase),
+ ]
+
+ self.assertFormal(m, mode="prove", depth=3)
if __name__ == "__main__":
projects / soc.git / blobdiff