-#define AC_ACCESS_REGISTER None
+#define DTM_IDCODE 0x01
/*
-* 2: Access the lowest 32 bits of the register.
+* Identifies the release version of this part.
+ */
+#define DTM_IDCODE_VERSION_OFFSET 28
+#define DTM_IDCODE_VERSION_LENGTH 4
+#define DTM_IDCODE_VERSION (0xf << DTM_IDCODE_VERSION_OFFSET)
+/*
+* Identifies the designer's part number of this part.
+ */
+#define DTM_IDCODE_PARTNUMBER_OFFSET 12
+#define DTM_IDCODE_PARTNUMBER_LENGTH 16
+#define DTM_IDCODE_PARTNUMBER (0xffff << DTM_IDCODE_PARTNUMBER_OFFSET)
+/*
+* Identifies the designer/manufacturer of this part. Bits 6:0 must be
+* bits 6:0 of the designer/manufacturer's Identification Code as
+* assigned by JEDEC Standard JEP106. Bits 10:7 contain the modulo-16
+* count of the number of continuation characters (0x7f) in that same
+* Identification Code.
+ */
+#define DTM_IDCODE_MANUFID_OFFSET 1
+#define DTM_IDCODE_MANUFID_LENGTH 11
+#define DTM_IDCODE_MANUFID (0x7ff << DTM_IDCODE_MANUFID_OFFSET)
+#define DTM_IDCODE_1_OFFSET 0
+#define DTM_IDCODE_1_LENGTH 1
+#define DTM_IDCODE_1 (0x1 << DTM_IDCODE_1_OFFSET)
+#define DTM_DTMCONTROL 0x10
+/*
+* Writing 1 to this bit resets the DMI controller, clearing any
+* sticky error state.
+ */
+#define DTM_DTMCONTROL_DMIRESET_OFFSET 16
+#define DTM_DTMCONTROL_DMIRESET_LENGTH 1
+#define DTM_DTMCONTROL_DMIRESET (0x1 << DTM_DTMCONTROL_DMIRESET_OFFSET)
+/*
+* This is the minimum number of cycles a debugger should spend in
+* Run-Test/Idle after every DMI scan to avoid a 'busy'
+* return code (\Fdmistat of 3). A debugger must still
+* check \Fdmistat when necessary.
*
-* 3: Access the lowest 64 bits of the register.
+* 0: It is not necessary to enter Run-Test/Idle at all.
*
-* 4: Access the lowest 128 bits of the register.
+* 1: Enter Run-Test/Idle and leave it immediately.
*
-* If \Fsize specifies a size larger than the register is, then the
-* access must fail. If a register is accessible, then \Fsize matching
-* the register's actual size must be supported.
+* 2: Enter Run-Test/Idle and stay there for 1 cycle before leaving.
+*
+* And so on.
*/
-#define AC_ACCESS_REGISTER_SIZE_OFFSET 19
-#define AC_ACCESS_REGISTER_SIZE_LENGTH 3
-#define AC_ACCESS_REGISTER_SIZE (0x7 << AC_ACCESS_REGISTER_SIZE_OFFSET)
+#define DTM_DTMCONTROL_IDLE_OFFSET 12
+#define DTM_DTMCONTROL_IDLE_LENGTH 3
+#define DTM_DTMCONTROL_IDLE (0x7 << DTM_DTMCONTROL_IDLE_OFFSET)
/*
-* When 1, execute the program in the Program Buffer exactly once
-* before performing the read/write.
+* 0: No error.
+*
+* 1: Reserved. Interpret the same as 2.
+*
+* 2: An operation failed (resulted in \Fop of 2).
+*
+* 3: An operation was attempted while a DMI access was still in
+* progress (resulted in \Fop of 3).
*/
-#define AC_ACCESS_REGISTER_PREEXEC_OFFSET 18
-#define AC_ACCESS_REGISTER_PREEXEC_LENGTH 1
-#define AC_ACCESS_REGISTER_PREEXEC (0x1 << AC_ACCESS_REGISTER_PREEXEC_OFFSET)
+#define DTM_DTMCONTROL_DMISTAT_OFFSET 10
+#define DTM_DTMCONTROL_DMISTAT_LENGTH 2
+#define DTM_DTMCONTROL_DMISTAT (0x3 << DTM_DTMCONTROL_DMISTAT_OFFSET)
/*
-* When 1, execute the program in the Program Buffer exactly once
-* after performing the read/write.
+* The size of \Faddress in \Rdmi.
*/
-#define AC_ACCESS_REGISTER_POSTEXEC_OFFSET 17
-#define AC_ACCESS_REGISTER_POSTEXEC_LENGTH 1
-#define AC_ACCESS_REGISTER_POSTEXEC (0x1 << AC_ACCESS_REGISTER_POSTEXEC_OFFSET)
+#define DTM_DTMCONTROL_ABITS_OFFSET 4
+#define DTM_DTMCONTROL_ABITS_LENGTH 6
+#define DTM_DTMCONTROL_ABITS (0x3f << DTM_DTMCONTROL_ABITS_OFFSET)
/*
-* 0: Copy data from {\tt arg0} portion of {\tt data} into the
-* specified register.
+* 0: Version described in spec version 0.11.
*
-* 1: Copy data from the specified register into {\tt arg0} portion
-* of {\tt data}.
+* 1: Version described in spec version 0.12 (and later?), which
+* reduces the DMI data width to 32 bits.
+*
+* Other values are reserved for future use.
*/
-#define AC_ACCESS_REGISTER_WRITE_OFFSET 16
-#define AC_ACCESS_REGISTER_WRITE_LENGTH 1
-#define AC_ACCESS_REGISTER_WRITE (0x1 << AC_ACCESS_REGISTER_WRITE_OFFSET)
+#define DTM_DTMCONTROL_VERSION_OFFSET 0
+#define DTM_DTMCONTROL_VERSION_LENGTH 4
+#define DTM_DTMCONTROL_VERSION (0xf << DTM_DTMCONTROL_VERSION_OFFSET)
+#define DTM_DMI 0x11
/*
-* Number of the register to access, as described in Table~\ref{tab:regno}.
+* Address used for DMI access. In Update-DR this value is used
+* to access the DM over the DMI.
*/
-#define AC_ACCESS_REGISTER_REGNO_OFFSET 0
-#define AC_ACCESS_REGISTER_REGNO_LENGTH 16
-#define AC_ACCESS_REGISTER_REGNO (0xffff << AC_ACCESS_REGISTER_REGNO_OFFSET)
-#define AC_QUICK_ACCESS None
-#define AC_QUICK_ACCESS_1_OFFSET 24
-#define AC_QUICK_ACCESS_1_LENGTH 8
-#define AC_QUICK_ACCESS_1 (0xff << AC_QUICK_ACCESS_1_OFFSET)
+#define DTM_DMI_ADDRESS_OFFSET 34
+#define DTM_DMI_ADDRESS_LENGTH abits
+#define DTM_DMI_ADDRESS (((1L<<abits)-1) << DTM_DMI_ADDRESS_OFFSET)
+/*
+* The data to send to the DM over the DMI during Update-DR, and
+* the data returned from the DM as a result of the previous operation.
+ */
+#define DTM_DMI_DATA_OFFSET 2
+#define DTM_DMI_DATA_LENGTH 32
+#define DTM_DMI_DATA (0xffffffffL << DTM_DMI_DATA_OFFSET)
+/*
+* When the debugger writes this field, it has the following meaning:
+*
+* 0: Ignore \Fdata. (nop)
+*
+* 1: Read from \Faddress. (read)
+*
+* 2: Write \Fdata to \Faddress. (write)
+*
+* 3: Reserved.
+*
+* When the debugger reads this field, it means the following:
+*
+* 0: The previous operation completed successfully.
+*
+* 1: Reserved.
+*
+* 2: A previous operation failed. The data scanned into \Rdmi in
+* this access will be ignored. This status is sticky and can be
+* cleared by writing \Fdmireset in \Rdtmcontrol.
+*
+* This indicates that the DM itself responded with an error, e.g.
+* in the System Bus and Serial Port overflow/underflow cases.
+*
+* 3: An operation was attempted while a DMI request is still in
+* progress. The data scanned into \Rdmi in this access will be
+* ignored. This status is sticky and can be cleared by writing
+* \Fdmireset in \Rdtmcontrol. If a debugger sees this status, it
+* needs to give the target more TCK edges between Update-DR and
+* Capture-DR. The simplest way to do that is to add extra transitions
+* in Run-Test/Idle.
+*
+* (The DTM, DM, and/or component may be in different clock domains,
+* so synchronization may be required. Some relatively fixed number of
+* TCK ticks may be needed for the request to reach the DM, complete,
+* and for the response to be synchronized back into the TCK domain.)
+ */
+#define DTM_DMI_OP_OFFSET 0
+#define DTM_DMI_OP_LENGTH 2
+#define DTM_DMI_OP (0x3L << DTM_DMI_OP_OFFSET)
#define CSR_DCSR 0x7b0
/*
* 0: There is no external debug support.
#define CSR_PRIV_PRV_OFFSET 0
#define CSR_PRIV_PRV_LENGTH 2
#define CSR_PRIV_PRV (0x3 << CSR_PRIV_PRV_OFFSET)
-#define DMI_DMCONTROL 0x00
-/*
-* Halt request signal for the hart selected by \Fhartsel. When 1, the
-* hart will halt if it's not currently halted.
-* Setting both \Fhaltreq and \Fresumereq leads to undefined behavior.
-*
-* Writes apply to the new value of \Fhartsel.
- */
-#define DMI_DMCONTROL_HALTREQ_OFFSET 31
-#define DMI_DMCONTROL_HALTREQ_LENGTH 1
-#define DMI_DMCONTROL_HALTREQ (0x1 << DMI_DMCONTROL_HALTREQ_OFFSET)
+#define CSR_TSELECT 0x7a0
+#define CSR_TSELECT_INDEX_OFFSET 0
+#define CSR_TSELECT_INDEX_LENGTH XLEN
+#define CSR_TSELECT_INDEX (((1L<<XLEN)-1) << CSR_TSELECT_INDEX_OFFSET)
+#define CSR_TDATA1 0x7a1
/*
-* Resume request signal for the hart selected by \Fhartsel. When 1,
-* the hart will resume if it's currently halted.
-* Setting both \Fhaltreq and \Fresumereq leads to undefined behavior.
+* 0: There is no trigger at this \Rtselect.
*
-* Writes apply to the new value of \Fhartsel.
- */
-#define DMI_DMCONTROL_RESUMEREQ_OFFSET 30
-#define DMI_DMCONTROL_RESUMEREQ_LENGTH 1
-#define DMI_DMCONTROL_RESUMEREQ (0x1 << DMI_DMCONTROL_RESUMEREQ_OFFSET)
-/*
-* The status of the currently selected hart.
+* 1: The trigger is a legacy SiFive address match trigger. These
+* should not be implemented and aren't further documented here.
*
-* 0: Halted.
+* 2: The trigger is an address/data match trigger. The remaining bits
+* in this register act as described in \Rmcontrol.
*
-* 1: Running.
+* 3: The trigger is an instruction count trigger. The remaining bits
+* in this register act as described in \Ricount.
*
-* 2: Unavailable (eg. powered down, held in reset).
+* 15: This trigger exists (so enumeration shouldn't terminate), but
+* is not currently available.
*
-* 3: \Fhartsel specifies a hart that does not exist in this system.
- */
-#define DMI_DMCONTROL_HARTSTATUS_OFFSET 26
-#define DMI_DMCONTROL_HARTSTATUS_LENGTH 2
-#define DMI_DMCONTROL_HARTSTATUS (0x3 << DMI_DMCONTROL_HARTSTATUS_OFFSET)
-/*
-* The DM-specific index of the hart to select.
+* Other values are reserved for future use.
*/
-#define DMI_DMCONTROL_HARTSEL_OFFSET 16
-#define DMI_DMCONTROL_HARTSEL_LENGTH 10
-#define DMI_DMCONTROL_HARTSEL (0x3ff << DMI_DMCONTROL_HARTSEL_OFFSET)
+#define CSR_TDATA1_TYPE_OFFSET XLEN-4
+#define CSR_TDATA1_TYPE_LENGTH 4
+#define CSR_TDATA1_TYPE (0xfL << CSR_TDATA1_TYPE_OFFSET)
/*
-* This bit serves as a reset signal for the Debug Module itself.
-* When 0, the module is held in reset. When 1, it functions normally.
-* No other mechanism should exist that may result in resetting the
-* Debug Module after power up, including the platform's system reset
-* or Debug Transport reset signals.
+* 0: Both Debug and M Mode can write the {\tt tdata} registers at the
+* selected \Rtselect.
*
-* A debugger should pulse this bit low to ensure that the Debug
-* Module is fully reset and ready to use.
+* 1: Only Halt Mode can write the {\tt tdata} registers at the
+* selected \Rtselect. Writes from other modes are ignored.
*
-* Implementations may use this bit to aid debugging, for example by
-* preventing the Debug Module from being power gated while debugging
-* is active.
+* This bit is only writable from Halt Mode.
*/
-#define DMI_DMCONTROL_DMACTIVE_OFFSET 9
-#define DMI_DMCONTROL_DMACTIVE_LENGTH 1
-#define DMI_DMCONTROL_DMACTIVE (0x1 << DMI_DMCONTROL_DMACTIVE_OFFSET)
+#define CSR_TDATA1_HMODE_OFFSET XLEN-5
+#define CSR_TDATA1_HMODE_LENGTH 1
+#define CSR_TDATA1_HMODE (0x1L << CSR_TDATA1_HMODE_OFFSET)
/*
-* This bit controls the reset signal from the DM to the rest of the
-* system. To perform a reset the debugger writes 1, and then writes 0
-* to deassert the reset.
+* Trigger-specific data.
*/
-#define DMI_DMCONTROL_RESET_OFFSET 8
-#define DMI_DMCONTROL_RESET_LENGTH 1
-#define DMI_DMCONTROL_RESET (0x1 << DMI_DMCONTROL_RESET_OFFSET)
+#define CSR_TDATA1_DATA_OFFSET 0
+#define CSR_TDATA1_DATA_LENGTH XLEN - 5
+#define CSR_TDATA1_DATA (((1L<<XLEN - 5)-1) << CSR_TDATA1_DATA_OFFSET)
+#define CSR_TDATA2 0x7a2
+#define CSR_TDATA2_DATA_OFFSET 0
+#define CSR_TDATA2_DATA_LENGTH XLEN
+#define CSR_TDATA2_DATA (((1L<<XLEN)-1) << CSR_TDATA2_DATA_OFFSET)
+#define CSR_TDATA3 0x7a3
+#define CSR_TDATA3_DATA_OFFSET 0
+#define CSR_TDATA3_DATA_LENGTH XLEN
+#define CSR_TDATA3_DATA (((1L<<XLEN)-1) << CSR_TDATA3_DATA_OFFSET)
+#define CSR_MCONTROL 0x7a1
+#define CSR_MCONTROL_TYPE_OFFSET XLEN-4
+#define CSR_MCONTROL_TYPE_LENGTH 4
+#define CSR_MCONTROL_TYPE (0xfL << CSR_MCONTROL_TYPE_OFFSET)
+#define CSR_MCONTROL_DMODE_OFFSET XLEN-5
+#define CSR_MCONTROL_DMODE_LENGTH 1
+#define CSR_MCONTROL_DMODE (0x1L << CSR_MCONTROL_DMODE_OFFSET)
/*
-* 0 when authentication is required before using the DM. 1 when the
-* authentication check has passed. On components that don't implement
-* authentication, this bit must be preset as 1.
+* Specifies the largest naturally aligned powers-of-two (NAPOT) range
+* supported by the hardware. The value is the logarithm base 2 of the
+* number of bytes in that range. A value of 0 indicates that only
+* exact value matches are supported (one byte range). A value of 63
+* corresponds to the maximum NAPOT range, which is $2^{63}$ bytes in
+* size.
*/
-#define DMI_DMCONTROL_AUTHENTICATED_OFFSET 7
-#define DMI_DMCONTROL_AUTHENTICATED_LENGTH 1
-#define DMI_DMCONTROL_AUTHENTICATED (0x1 << DMI_DMCONTROL_AUTHENTICATED_OFFSET)
+#define CSR_MCONTROL_MASKMAX_OFFSET XLEN-11
+#define CSR_MCONTROL_MASKMAX_LENGTH 6
+#define CSR_MCONTROL_MASKMAX (0x3fL << CSR_MCONTROL_MASKMAX_OFFSET)
/*
-* While 1, writes to \Rauthdatazero and \Rauthdataone may be ignored
-* or may result in authentication failing. Authentication mechanisms
-* that are slow (or intentionally delayed) must set this bit when
-* they're not ready to process another write.
+* 0: Perform a match on the address.
+*
+* 1: Perform a match on the data value loaded/stored, or the
+* instruction executed.
*/
-#define DMI_DMCONTROL_AUTHBUSY_OFFSET 6
-#define DMI_DMCONTROL_AUTHBUSY_LENGTH 1
-#define DMI_DMCONTROL_AUTHBUSY (0x1 << DMI_DMCONTROL_AUTHBUSY_OFFSET)
+#define CSR_MCONTROL_SELECT_OFFSET 19
+#define CSR_MCONTROL_SELECT_LENGTH 1
+#define CSR_MCONTROL_SELECT (0x1L << CSR_MCONTROL_SELECT_OFFSET)
/*
-* Defines the kind of authentication required to use this DM.
+* 0: The action for this trigger will be taken just before the
+* instruction that triggered it is executed, but after all preceding
+* instructions are are committed.
*
-* 0: No authentication is required.
+* 1: The action for this trigger will be taken after the instruction
+* that triggered it is executed. It should be taken before the next
+* instruction is executed, but it is better to implement triggers and
+* not implement that suggestion than to not implement them at all.
*
-* 1: A password is required.
+* Most hardware will only implement one timing or the other, possibly
+* dependent on \Fselect, \Fexecute, \Fload, and \Fstore. This bit
+* primarily exists for the hardware to communicate to the debugger
+* what will happen. Hardware may implement the bit fully writable, in
+* which case the debugger has a little more control.
*
-* 2: A challenge-response mechanism is in place.
+* Data load triggers with \Ftiming of 0 will result in the same load
+* happening again when the debugger lets the core run. For data load
+* triggers debuggers must first attempt to set the breakpoint with
+* \Ftiming of 1.
*
-* 3: Reserved for future use.
+* A chain of triggers that don't all have the same \Ftiming value
+* will never fire (unless consecutive instructions match the
+* appropriate triggers).
*/
-#define DMI_DMCONTROL_AUTHTYPE_OFFSET 4
-#define DMI_DMCONTROL_AUTHTYPE_LENGTH 2
-#define DMI_DMCONTROL_AUTHTYPE (0x3 << DMI_DMCONTROL_AUTHTYPE_OFFSET)
+#define CSR_MCONTROL_TIMING_OFFSET 18
+#define CSR_MCONTROL_TIMING_LENGTH 1
+#define CSR_MCONTROL_TIMING (0x1L << CSR_MCONTROL_TIMING_OFFSET)
/*
-* 0: There is no Debug Module present.
+* Determines what happens when this trigger matches.
*
-* 1: There is a Debug Module and it conforms to version 0.12 of this
-* specification.
+* 0: Raise a breakpoint exception. (Used when software wants to use
+* the trigger module without an external debugger attached.)
*
-* Other values are reserved for future use.
- */
-#define DMI_DMCONTROL_VERSION_OFFSET 0
-#define DMI_DMCONTROL_VERSION_LENGTH 4
-#define DMI_DMCONTROL_VERSION (0xf << DMI_DMCONTROL_VERSION_OFFSET)
-#define DMI_HARTINFO 0x01
-/*
-* 0: The {\tt data} registers are shadowed in the hart by CSR
-* registers. Each CSR register is XLEN bits in size, and corresponds
-* to a single argument, per Table~\ref{tab:datareg}.
+* 1: Enter Halt Mode. (Only supported when \Fhmode is 1.)
*
-* 1: The {\tt data} registers are shadowed in the hart's memory map.
-* Each register takes up 4 bytes in the memory map.
- */
-#define DMI_HARTINFO_DATAACCESS_OFFSET 16
-#define DMI_HARTINFO_DATAACCESS_LENGTH 1
-#define DMI_HARTINFO_DATAACCESS (0x1 << DMI_HARTINFO_DATAACCESS_OFFSET)
-/*
-* If \Fdataaccess is 0: Number of CSR registers dedicated to
-* shadowing the {\tt data} registers.
+* 2: Start tracing.
*
-* If \Fdataaccess is 1: Number of 32-bit words in the memory map
-* dedicated to shadowing the {\tt data} registers.
- */
-#define DMI_HARTINFO_DATASIZE_OFFSET 12
-#define DMI_HARTINFO_DATASIZE_LENGTH 4
-#define DMI_HARTINFO_DATASIZE (0xf << DMI_HARTINFO_DATASIZE_OFFSET)
-/*
-* If \Fdataaccess is 0: The number of the first CSR dedicated to
-* shadowing the {\tt data} registers.
+* 3: Stop tracing.
*
-* If \Fdataaccess is 1: Signed address of RAM where the {\tt data}
-* registers are shadowed.
+* 4: Emit trace data for this match. If it is a data access match,
+* emit appropriate Load/Store Address/Data. If it is an instruction
+* execution, emit its PC.
+*
+* Other values are reserved for future use.
*/
-#define DMI_HARTINFO_DATAADDR_OFFSET 0
-#define DMI_HARTINFO_DATAADDR_LENGTH 12
-#define DMI_HARTINFO_DATAADDR (0xfff << DMI_HARTINFO_DATAADDR_OFFSET)
-#define DMI_HALTSUM 0x02
-#define DMI_HALTSUM_HALT1023_992_OFFSET 31
-#define DMI_HALTSUM_HALT1023_992_LENGTH 1
-#define DMI_HALTSUM_HALT1023_992 (0x1 << DMI_HALTSUM_HALT1023_992_OFFSET)
-#define DMI_HALTSUM_HALT991_960_OFFSET 30
-#define DMI_HALTSUM_HALT991_960_LENGTH 1
-#define DMI_HALTSUM_HALT991_960 (0x1 << DMI_HALTSUM_HALT991_960_OFFSET)
-#define DMI_HALTSUM_HALT959_928_OFFSET 29
-#define DMI_HALTSUM_HALT959_928_LENGTH 1
-#define DMI_HALTSUM_HALT959_928 (0x1 << DMI_HALTSUM_HALT959_928_OFFSET)
-#define DMI_HALTSUM_HALT927_896_OFFSET 28
-#define DMI_HALTSUM_HALT927_896_LENGTH 1
-#define DMI_HALTSUM_HALT927_896 (0x1 << DMI_HALTSUM_HALT927_896_OFFSET)
-#define DMI_HALTSUM_HALT895_864_OFFSET 27
-#define DMI_HALTSUM_HALT895_864_LENGTH 1
-#define DMI_HALTSUM_HALT895_864 (0x1 << DMI_HALTSUM_HALT895_864_OFFSET)
-#define DMI_HALTSUM_HALT863_832_OFFSET 26
-#define DMI_HALTSUM_HALT863_832_LENGTH 1
-#define DMI_HALTSUM_HALT863_832 (0x1 << DMI_HALTSUM_HALT863_832_OFFSET)
-#define DMI_HALTSUM_HALT831_800_OFFSET 25
-#define DMI_HALTSUM_HALT831_800_LENGTH 1
-#define DMI_HALTSUM_HALT831_800 (0x1 << DMI_HALTSUM_HALT831_800_OFFSET)
-#define DMI_HALTSUM_HALT799_768_OFFSET 24
-#define DMI_HALTSUM_HALT799_768_LENGTH 1
-#define DMI_HALTSUM_HALT799_768 (0x1 << DMI_HALTSUM_HALT799_768_OFFSET)
-#define DMI_HALTSUM_HALT767_736_OFFSET 23
-#define DMI_HALTSUM_HALT767_736_LENGTH 1
-#define DMI_HALTSUM_HALT767_736 (0x1 << DMI_HALTSUM_HALT767_736_OFFSET)
-#define DMI_HALTSUM_HALT735_704_OFFSET 22
-#define DMI_HALTSUM_HALT735_704_LENGTH 1
-#define DMI_HALTSUM_HALT735_704 (0x1 << DMI_HALTSUM_HALT735_704_OFFSET)
-#define DMI_HALTSUM_HALT703_672_OFFSET 21
-#define DMI_HALTSUM_HALT703_672_LENGTH 1
-#define DMI_HALTSUM_HALT703_672 (0x1 << DMI_HALTSUM_HALT703_672_OFFSET)
-#define DMI_HALTSUM_HALT671_640_OFFSET 20
-#define DMI_HALTSUM_HALT671_640_LENGTH 1
-#define DMI_HALTSUM_HALT671_640 (0x1 << DMI_HALTSUM_HALT671_640_OFFSET)
-#define DMI_HALTSUM_HALT639_608_OFFSET 19
-#define DMI_HALTSUM_HALT639_608_LENGTH 1
-#define DMI_HALTSUM_HALT639_608 (0x1 << DMI_HALTSUM_HALT639_608_OFFSET)
-#define DMI_HALTSUM_HALT607_576_OFFSET 18
-#define DMI_HALTSUM_HALT607_576_LENGTH 1
-#define DMI_HALTSUM_HALT607_576 (0x1 << DMI_HALTSUM_HALT607_576_OFFSET)
-#define DMI_HALTSUM_HALT575_544_OFFSET 17
-#define DMI_HALTSUM_HALT575_544_LENGTH 1
-#define DMI_HALTSUM_HALT575_544 (0x1 << DMI_HALTSUM_HALT575_544_OFFSET)
-#define DMI_HALTSUM_HALT543_512_OFFSET 16
-#define DMI_HALTSUM_HALT543_512_LENGTH 1
-#define DMI_HALTSUM_HALT543_512 (0x1 << DMI_HALTSUM_HALT543_512_OFFSET)
-#define DMI_HALTSUM_HALT511_480_OFFSET 15
-#define DMI_HALTSUM_HALT511_480_LENGTH 1
-#define DMI_HALTSUM_HALT511_480 (0x1 << DMI_HALTSUM_HALT511_480_OFFSET)
-#define DMI_HALTSUM_HALT479_448_OFFSET 14
-#define DMI_HALTSUM_HALT479_448_LENGTH 1
-#define DMI_HALTSUM_HALT479_448 (0x1 << DMI_HALTSUM_HALT479_448_OFFSET)
-#define DMI_HALTSUM_HALT447_416_OFFSET 13
-#define DMI_HALTSUM_HALT447_416_LENGTH 1
-#define DMI_HALTSUM_HALT447_416 (0x1 << DMI_HALTSUM_HALT447_416_OFFSET)
-#define DMI_HALTSUM_HALT415_384_OFFSET 12
-#define DMI_HALTSUM_HALT415_384_LENGTH 1
-#define DMI_HALTSUM_HALT415_384 (0x1 << DMI_HALTSUM_HALT415_384_OFFSET)
-#define DMI_HALTSUM_HALT383_352_OFFSET 11
-#define DMI_HALTSUM_HALT383_352_LENGTH 1
-#define DMI_HALTSUM_HALT383_352 (0x1 << DMI_HALTSUM_HALT383_352_OFFSET)
-#define DMI_HALTSUM_HALT351_320_OFFSET 10
-#define DMI_HALTSUM_HALT351_320_LENGTH 1
-#define DMI_HALTSUM_HALT351_320 (0x1 << DMI_HALTSUM_HALT351_320_OFFSET)
-#define DMI_HALTSUM_HALT319_288_OFFSET 9
-#define DMI_HALTSUM_HALT319_288_LENGTH 1
-#define DMI_HALTSUM_HALT319_288 (0x1 << DMI_HALTSUM_HALT319_288_OFFSET)
-#define DMI_HALTSUM_HALT287_256_OFFSET 8
-#define DMI_HALTSUM_HALT287_256_LENGTH 1
-#define DMI_HALTSUM_HALT287_256 (0x1 << DMI_HALTSUM_HALT287_256_OFFSET)
-#define DMI_HALTSUM_HALT255_224_OFFSET 7
-#define DMI_HALTSUM_HALT255_224_LENGTH 1
-#define DMI_HALTSUM_HALT255_224 (0x1 << DMI_HALTSUM_HALT255_224_OFFSET)
-#define DMI_HALTSUM_HALT223_192_OFFSET 6
-#define DMI_HALTSUM_HALT223_192_LENGTH 1
-#define DMI_HALTSUM_HALT223_192 (0x1 << DMI_HALTSUM_HALT223_192_OFFSET)
-#define DMI_HALTSUM_HALT191_160_OFFSET 5
-#define DMI_HALTSUM_HALT191_160_LENGTH 1
-#define DMI_HALTSUM_HALT191_160 (0x1 << DMI_HALTSUM_HALT191_160_OFFSET)
-#define DMI_HALTSUM_HALT159_128_OFFSET 4
-#define DMI_HALTSUM_HALT159_128_LENGTH 1
-#define DMI_HALTSUM_HALT159_128 (0x1 << DMI_HALTSUM_HALT159_128_OFFSET)
-#define DMI_HALTSUM_HALT127_96_OFFSET 3
-#define DMI_HALTSUM_HALT127_96_LENGTH 1
-#define DMI_HALTSUM_HALT127_96 (0x1 << DMI_HALTSUM_HALT127_96_OFFSET)
-#define DMI_HALTSUM_HALT95_64_OFFSET 2
-#define DMI_HALTSUM_HALT95_64_LENGTH 1
-#define DMI_HALTSUM_HALT95_64 (0x1 << DMI_HALTSUM_HALT95_64_OFFSET)
-#define DMI_HALTSUM_HALT63_32_OFFSET 1
-#define DMI_HALTSUM_HALT63_32_LENGTH 1
-#define DMI_HALTSUM_HALT63_32 (0x1 << DMI_HALTSUM_HALT63_32_OFFSET)
-#define DMI_HALTSUM_HALT31_0_OFFSET 0
-#define DMI_HALTSUM_HALT31_0_LENGTH 1
-#define DMI_HALTSUM_HALT31_0 (0x1 << DMI_HALTSUM_HALT31_0_OFFSET)
-#define DMI_SBCS 0x03
+#define CSR_MCONTROL_ACTION_OFFSET 12
+#define CSR_MCONTROL_ACTION_LENGTH 6
+#define CSR_MCONTROL_ACTION (0x3fL << CSR_MCONTROL_ACTION_OFFSET)
/*
-* When a 1 is written here, triggers a read at the address in {\tt
-* sbaddress} using the access size set by \Fsbaccess.
+* 0: When this trigger matches, the configured action is taken.
+*
+* 1: While this trigger does not match, it prevents the trigger with
+* the next index from matching.
*/
-#define DMI_SBCS_SBSINGLEREAD_OFFSET 20
-#define DMI_SBCS_SBSINGLEREAD_LENGTH 1
-#define DMI_SBCS_SBSINGLEREAD (0x1 << DMI_SBCS_SBSINGLEREAD_OFFSET)
+#define CSR_MCONTROL_CHAIN_OFFSET 11
+#define CSR_MCONTROL_CHAIN_LENGTH 1
+#define CSR_MCONTROL_CHAIN (0x1L << CSR_MCONTROL_CHAIN_OFFSET)
/*
-* Select the access size to use for system bus accesses triggered by
-* writes to the {\tt sbaddress} registers or \Rsbdatazero.
+* 0: Matches when the value equals \Rtdatatwo.
*
-* 0: 8-bit
+* 1: Matches when the top M bits of the value match the top M bits of
+* \Rtdatatwo. M is XLEN-1 minus the index of the least-significant
+* bit containing 0 in \Rtdatatwo.
*
-* 1: 16-bit
+* 2: Matches when the value is greater than or equal to \Rtdatatwo.
*
-* 2: 32-bit
+* 3: Matches when the value is less than \Rtdatatwo.
*
-* 3: 64-bit
+* 4: Matches when the lower half of the value equals the lower half
+* of \Rtdatatwo after the lower half of the value is ANDed with the
+* upper half of \Rtdatatwo.
*
-* 4: 128-bit
+* 5: Matches when the upper half of the value equals the lower half
+* of \Rtdatatwo after the upper half of the value is ANDed with the
+* upper half of \Rtdatatwo.
*
-* If an unsupported system bus access size is written here,
-* the DM may not
-* perform the access, or may perform the access with any access size
+* Other values are reserved for future use.
*/
-#define DMI_SBCS_SBACCESS_OFFSET 17
-#define DMI_SBCS_SBACCESS_LENGTH 3
-#define DMI_SBCS_SBACCESS (0x7 << DMI_SBCS_SBACCESS_OFFSET)
+#define CSR_MCONTROL_MATCH_OFFSET 7
+#define CSR_MCONTROL_MATCH_LENGTH 4
+#define CSR_MCONTROL_MATCH (0xfL << CSR_MCONTROL_MATCH_OFFSET)
/*
-* When 1, the internal address value (used by the system bus master)
-* is incremented by the access size (in bytes) selected in \Fsbaccess
-* after every system bus access.
+* When set, enable this trigger in M mode.
*/
-#define DMI_SBCS_SBAUTOINCREMENT_OFFSET 16
-#define DMI_SBCS_SBAUTOINCREMENT_LENGTH 1
-#define DMI_SBCS_SBAUTOINCREMENT (0x1 << DMI_SBCS_SBAUTOINCREMENT_OFFSET)
+#define CSR_MCONTROL_M_OFFSET 6
+#define CSR_MCONTROL_M_LENGTH 1
+#define CSR_MCONTROL_M (0x1L << CSR_MCONTROL_M_OFFSET)
/*
-* When 1, every read from \Rsbdatazero automatically triggers a system
-* bus read at the new address.
+* When set, enable this trigger in H mode.
*/
-#define DMI_SBCS_SBAUTOREAD_OFFSET 15
-#define DMI_SBCS_SBAUTOREAD_LENGTH 1
-#define DMI_SBCS_SBAUTOREAD (0x1 << DMI_SBCS_SBAUTOREAD_OFFSET)
+#define CSR_MCONTROL_H_OFFSET 5
+#define CSR_MCONTROL_H_LENGTH 1
+#define CSR_MCONTROL_H (0x1L << CSR_MCONTROL_H_OFFSET)
/*
-* When the debug module's system bus
-* master causes a bus error, this field gets set.
-* It remains set until 0 is written to any bit in this field. Until
-* that happens, the system bus master is busy and no more accesses can be
-* initiated by the debug module.
-*
-* 0: There was no bus error.
-*
-* 1: There was a timeout.
-*
-* 2: A bad address was accessed.
-*
-* 3: There was some other error (eg. alignment).
-*
-* 4: The system bus master was busy when a one of the
-* {\tt sbaddress} or {\tt sbdata} registers was written,
-* or the {\tt sbdata} register was read when it had
-* stale data.
+* When set, enable this trigger in S mode.
*/
-#define DMI_SBCS_SBERROR_OFFSET 12
-#define DMI_SBCS_SBERROR_LENGTH 3
-#define DMI_SBCS_SBERROR (0x7 << DMI_SBCS_SBERROR_OFFSET)
+#define CSR_MCONTROL_S_OFFSET 4
+#define CSR_MCONTROL_S_LENGTH 1
+#define CSR_MCONTROL_S (0x1L << CSR_MCONTROL_S_OFFSET)
/*
-* Width of system bus addresses in bits. (0 indicates there is no bus
-* access support.)
+* When set, enable this trigger in U mode.
*/
-#define DMI_SBCS_SBASIZE_OFFSET 5
-#define DMI_SBCS_SBASIZE_LENGTH 7
-#define DMI_SBCS_SBASIZE (0x7f << DMI_SBCS_SBASIZE_OFFSET)
+#define CSR_MCONTROL_U_OFFSET 3
+#define CSR_MCONTROL_U_LENGTH 1
+#define CSR_MCONTROL_U (0x1L << CSR_MCONTROL_U_OFFSET)
/*
-* 1 when 128-bit system bus accesses are supported.
+* When set, the trigger fires on the address or opcode of an
+* instruction that is executed.
*/
-#define DMI_SBCS_SBACCESS128_OFFSET 4
-#define DMI_SBCS_SBACCESS128_LENGTH 1
-#define DMI_SBCS_SBACCESS128 (0x1 << DMI_SBCS_SBACCESS128_OFFSET)
+#define CSR_MCONTROL_EXECUTE_OFFSET 2
+#define CSR_MCONTROL_EXECUTE_LENGTH 1
+#define CSR_MCONTROL_EXECUTE (0x1L << CSR_MCONTROL_EXECUTE_OFFSET)
/*
-* 1 when 64-bit system bus accesses are supported.
+* When set, the trigger fires on the address or data of a store.
*/
-#define DMI_SBCS_SBACCESS64_OFFSET 3
-#define DMI_SBCS_SBACCESS64_LENGTH 1
-#define DMI_SBCS_SBACCESS64 (0x1 << DMI_SBCS_SBACCESS64_OFFSET)
+#define CSR_MCONTROL_STORE_OFFSET 1
+#define CSR_MCONTROL_STORE_LENGTH 1
+#define CSR_MCONTROL_STORE (0x1L << CSR_MCONTROL_STORE_OFFSET)
/*
-* 1 when 32-bit system bus accesses are supported.
+* When set, the trigger fires on the address or data of a load.
*/
-#define DMI_SBCS_SBACCESS32_OFFSET 2
-#define DMI_SBCS_SBACCESS32_LENGTH 1
-#define DMI_SBCS_SBACCESS32 (0x1 << DMI_SBCS_SBACCESS32_OFFSET)
+#define CSR_MCONTROL_LOAD_OFFSET 0
+#define CSR_MCONTROL_LOAD_LENGTH 1
+#define CSR_MCONTROL_LOAD (0x1L << CSR_MCONTROL_LOAD_OFFSET)
+#define CSR_ICOUNT 0x7a1
+#define CSR_ICOUNT_TYPE_OFFSET XLEN-4
+#define CSR_ICOUNT_TYPE_LENGTH 4
+#define CSR_ICOUNT_TYPE (0xfL << CSR_ICOUNT_TYPE_OFFSET)
+#define CSR_ICOUNT_DMODE_OFFSET XLEN-5
+#define CSR_ICOUNT_DMODE_LENGTH 1
+#define CSR_ICOUNT_DMODE (0x1L << CSR_ICOUNT_DMODE_OFFSET)
/*
-* 1 when 16-bit system bus accesses are supported.
+* When count is decremented to 0, the trigger fires. Instead of
+* changing \Fcount from 1 to 0, it is also acceptable for hardware to
+* clear \Fm, \Fh, \Fs, and \Fu. This allows \Fcount to be hard-wired
+* to 1 if this register just exists for single step.
*/
-#define DMI_SBCS_SBACCESS16_OFFSET 1
-#define DMI_SBCS_SBACCESS16_LENGTH 1
-#define DMI_SBCS_SBACCESS16 (0x1 << DMI_SBCS_SBACCESS16_OFFSET)
+#define CSR_ICOUNT_COUNT_OFFSET 10
+#define CSR_ICOUNT_COUNT_LENGTH 14
+#define CSR_ICOUNT_COUNT (0x3fffL << CSR_ICOUNT_COUNT_OFFSET)
/*
-* 1 when 8-bit system bus accesses are supported.
+* When set, every instruction completed in M mode decrements \Fcount
+* by 1.
*/
-#define DMI_SBCS_SBACCESS8_OFFSET 0
-#define DMI_SBCS_SBACCESS8_LENGTH 1
-#define DMI_SBCS_SBACCESS8 (0x1 << DMI_SBCS_SBACCESS8_OFFSET)
-#define DMI_SBADDRESS0 0x04
+#define CSR_ICOUNT_M_OFFSET 9
+#define CSR_ICOUNT_M_LENGTH 1
+#define CSR_ICOUNT_M (0x1L << CSR_ICOUNT_M_OFFSET)
/*
-* Accesses bits 31:0 of the internal address.
+* When set, every instruction completed in H mode decrements \Fcount
+* by 1.
*/
-#define DMI_SBADDRESS0_ADDRESS_OFFSET 0
-#define DMI_SBADDRESS0_ADDRESS_LENGTH 32
-#define DMI_SBADDRESS0_ADDRESS (0xffffffff << DMI_SBADDRESS0_ADDRESS_OFFSET)
-#define DMI_SBADDRESS1 0x05
+#define CSR_ICOUNT_H_OFFSET 8
+#define CSR_ICOUNT_H_LENGTH 1
+#define CSR_ICOUNT_H (0x1L << CSR_ICOUNT_H_OFFSET)
/*
-* Accesses bits 63:32 of the internal address (if the system address
-* bus is that wide).
+* When set, every instruction completed in S mode decrements \Fcount
+* by 1.
*/
-#define DMI_SBADDRESS1_ADDRESS_OFFSET 0
-#define DMI_SBADDRESS1_ADDRESS_LENGTH 32
-#define DMI_SBADDRESS1_ADDRESS (0xffffffff << DMI_SBADDRESS1_ADDRESS_OFFSET)
-#define DMI_SBADDRESS2 0x06
+#define CSR_ICOUNT_S_OFFSET 7
+#define CSR_ICOUNT_S_LENGTH 1
+#define CSR_ICOUNT_S (0x1L << CSR_ICOUNT_S_OFFSET)
/*
-* The same as \Fbusy in \Rsbaddresszero.
+* When set, every instruction completed in U mode decrements \Fcount
+* by 1.
*/
-#define DMI_SBADDRESS2_BUSY_OFFSET 31
-#define DMI_SBADDRESS2_BUSY_LENGTH 1
-#define DMI_SBADDRESS2_BUSY (0x1 << DMI_SBADDRESS2_BUSY_OFFSET)
+#define CSR_ICOUNT_U_OFFSET 6
+#define CSR_ICOUNT_U_LENGTH 1
+#define CSR_ICOUNT_U (0x1L << CSR_ICOUNT_U_OFFSET)
/*
-* Accesses bits 91:61 of the internal address (if the system address
-* bus is that wide).
+* Determines what happens when this trigger matches.
+*
+* 0: Raise a debug exception. (Used when software wants to use the
+* trigger module without an external debugger attached.)
+*
+* 1: Enter Halt Mode. (Only supported when \Fhmode is 1.)
+*
+* 2: Start tracing.
+*
+* 3: Stop tracing.
+*
+* 4: Emit trace data for this match. If it is a data access match,
+* emit appropriate Load/Store Address/Data. If it is an instruction
+* execution, emit its PC.
+*
+* Other values are reserved for future use.
*/
-#define DMI_SBADDRESS2_ADDRESS_OFFSET 0
-#define DMI_SBADDRESS2_ADDRESS_LENGTH 31
-#define DMI_SBADDRESS2_ADDRESS (0x7fffffff << DMI_SBADDRESS2_ADDRESS_OFFSET)
-#define DMI_SBDATA0 0x07
+#define CSR_ICOUNT_ACTION_OFFSET 0
+#define CSR_ICOUNT_ACTION_LENGTH 6
+#define CSR_ICOUNT_ACTION (0x3fL << CSR_ICOUNT_ACTION_OFFSET)
+#define DMI_DMCONTROL 0x00
/*
-* Accesses bits 31:0 of the internal data.
+* Halt request signal for the hart selected by \Fhartsel. When 1, the
+* hart will halt if it's not currently halted.
+* Setting both \Fhaltreq and \Fresumereq leads to undefined behavior.
+*
+* Writes apply to the new value of \Fhartsel.
*/
-#define DMI_SBDATA0_DATA_OFFSET 0
-#define DMI_SBDATA0_DATA_LENGTH 32
-#define DMI_SBDATA0_DATA (0xffffffff << DMI_SBDATA0_DATA_OFFSET)
-#define DMI_SBDATA1 0x08
+#define DMI_DMCONTROL_HALTREQ_OFFSET 31
+#define DMI_DMCONTROL_HALTREQ_LENGTH 1
+#define DMI_DMCONTROL_HALTREQ (0x1 << DMI_DMCONTROL_HALTREQ_OFFSET)
/*
-* Accesses bits 63:32 of the internal data (if the system bus is
-* that wide).
+* Resume request signal for the hart selected by \Fhartsel. When 1,
+* the hart will resume if it's currently halted.
+* Setting both \Fhaltreq and \Fresumereq leads to undefined behavior.
+*
+* Writes apply to the new value of \Fhartsel.
*/
-#define DMI_SBDATA1_DATA_OFFSET 0
-#define DMI_SBDATA1_DATA_LENGTH 32
-#define DMI_SBDATA1_DATA (0xffffffff << DMI_SBDATA1_DATA_OFFSET)
-#define DMI_SBDATA2 0x09
+#define DMI_DMCONTROL_RESUMEREQ_OFFSET 30
+#define DMI_DMCONTROL_RESUMEREQ_LENGTH 1
+#define DMI_DMCONTROL_RESUMEREQ (0x1 << DMI_DMCONTROL_RESUMEREQ_OFFSET)
/*
-* Accesses bits 95:64 of the internal data (if the system bus is
-* that wide).
+* The status of the currently selected hart.
+*
+* 0: Halted.
+*
+* 1: Running.
+*
+* 2: Unavailable (eg. powered down, held in reset).
+*
+* 3: \Fhartsel specifies a hart that does not exist in this system.
*/
-#define DMI_SBDATA2_DATA_OFFSET 0
-#define DMI_SBDATA2_DATA_LENGTH 32
-#define DMI_SBDATA2_DATA (0xffffffff << DMI_SBDATA2_DATA_OFFSET)
-#define DMI_SBDATA3 0x0a
+#define DMI_DMCONTROL_HARTSTATUS_OFFSET 26
+#define DMI_DMCONTROL_HARTSTATUS_LENGTH 2
+#define DMI_DMCONTROL_HARTSTATUS (0x3 << DMI_DMCONTROL_HARTSTATUS_OFFSET)
/*
-* Accesses bits 127:96 of the internal data (if the system bus is
-* that wide).
+* The DM-specific index of the hart to select.
*/
-#define DMI_SBDATA3_DATA_OFFSET 0
-#define DMI_SBDATA3_DATA_LENGTH 32
-#define DMI_SBDATA3_DATA (0xffffffff << DMI_SBDATA3_DATA_OFFSET)
-#define DMI_AUTHDATA0 0x0b
-#define DMI_AUTHDATA0_DATA_OFFSET 0
-#define DMI_AUTHDATA0_DATA_LENGTH 32
-#define DMI_AUTHDATA0_DATA (0xffffffff << DMI_AUTHDATA0_DATA_OFFSET)
-#define DMI_AUTHDATA1 0x0c
-#define DMI_AUTHDATA1_DATA_OFFSET 0
-#define DMI_AUTHDATA1_DATA_LENGTH 32
-#define DMI_AUTHDATA1_DATA (0xffffffff << DMI_AUTHDATA1_DATA_OFFSET)
-#define DMI_ABSTRACTCS 0x0e
-#define DMI_ABSTRACTCS_AUTOEXEC7_OFFSET 15
-#define DMI_ABSTRACTCS_AUTOEXEC7_LENGTH 1
-#define DMI_ABSTRACTCS_AUTOEXEC7 (0x1 << DMI_ABSTRACTCS_AUTOEXEC7_OFFSET)
-#define DMI_ABSTRACTCS_AUTOEXEC6_OFFSET 14
-#define DMI_ABSTRACTCS_AUTOEXEC6_LENGTH 1
-#define DMI_ABSTRACTCS_AUTOEXEC6 (0x1 << DMI_ABSTRACTCS_AUTOEXEC6_OFFSET)
-#define DMI_ABSTRACTCS_AUTOEXEC5_OFFSET 13
-#define DMI_ABSTRACTCS_AUTOEXEC5_LENGTH 1
-#define DMI_ABSTRACTCS_AUTOEXEC5 (0x1 << DMI_ABSTRACTCS_AUTOEXEC5_OFFSET)
-#define DMI_ABSTRACTCS_AUTOEXEC4_OFFSET 12
-#define DMI_ABSTRACTCS_AUTOEXEC4_LENGTH 1
-#define DMI_ABSTRACTCS_AUTOEXEC4 (0x1 << DMI_ABSTRACTCS_AUTOEXEC4_OFFSET)
-#define DMI_ABSTRACTCS_AUTOEXEC3_OFFSET 11
-#define DMI_ABSTRACTCS_AUTOEXEC3_LENGTH 1
-#define DMI_ABSTRACTCS_AUTOEXEC3 (0x1 << DMI_ABSTRACTCS_AUTOEXEC3_OFFSET)
-#define DMI_ABSTRACTCS_AUTOEXEC2_OFFSET 10
-#define DMI_ABSTRACTCS_AUTOEXEC2_LENGTH 1
-#define DMI_ABSTRACTCS_AUTOEXEC2 (0x1 << DMI_ABSTRACTCS_AUTOEXEC2_OFFSET)
-#define DMI_ABSTRACTCS_AUTOEXEC1_OFFSET 9
-#define DMI_ABSTRACTCS_AUTOEXEC1_LENGTH 1
-#define DMI_ABSTRACTCS_AUTOEXEC1 (0x1 << DMI_ABSTRACTCS_AUTOEXEC1_OFFSET)
+#define DMI_DMCONTROL_HARTSEL_OFFSET 16
+#define DMI_DMCONTROL_HARTSEL_LENGTH 10
+#define DMI_DMCONTROL_HARTSEL (0x3ff << DMI_DMCONTROL_HARTSEL_OFFSET)
/*
-* When 1, accesses to \Rdatazero cause the command in \Rcommand to be
-* executed again.
+* This optional bit controls reset to the currently selected hart. To
+* perform a reset the debugger writes 1, and then writes 0 to
+* deassert the reset signal.
*
-* The same is true for other other autoexec bits: When 1, accesses to
-* {\tt data}N cause the command in \Rcommand to be executed again.
+* If this feature is not implemented, the bit always stays 0, so
+* after writing 1 the debugger can read the register back to see if
+* the feature is supported.
*/
-#define DMI_ABSTRACTCS_AUTOEXEC0_OFFSET 8
-#define DMI_ABSTRACTCS_AUTOEXEC0_LENGTH 1
-#define DMI_ABSTRACTCS_AUTOEXEC0 (0x1 << DMI_ABSTRACTCS_AUTOEXEC0_OFFSET)
+#define DMI_DMCONTROL_HARTRESET_OFFSET 10
+#define DMI_DMCONTROL_HARTRESET_LENGTH 1
+#define DMI_DMCONTROL_HARTRESET (0x1 << DMI_DMCONTROL_HARTRESET_OFFSET)
/*
-* Gets set if an abstract command fails. No abstract command is
-* started until the value is reset to 0.
-*
-* 0 (none): No error.
+* This bit serves as a reset signal for the Debug Module itself.
*
-* 1 (busy): An abstract command was executing while \Rcommand or one
-* of the {\tt data} registers was accessed.
+* 0: The module, including authentication mechanism, is held in
+* reset.
*
-* 2 (not supported): The requested command is not supported. A
-* command that is not supported while the hart is running may be
-* supported when it is halted.
+* 1: The module functions normally.
*
-* 3 (exception): An exception occurred while executing the command
-* (eg. while executing the Program Buffer).
+* No other mechanism should exist that may result in resetting the
+* Debug Module after power up, including the platform's system reset
+* or Debug Transport reset signals.
*
-* 4 (halt/resume): An abstract command couldn't execute because the
-* hart wasn't in the expected state (running/halted).
+* A debugger should pulse this bit low to ensure that the Debug
+* Module is fully reset and ready to use.
*
-* 7 (other): The command failed for another reason.
+* Implementations may use this bit to aid debugging, for example by
+* preventing the Debug Module from being power gated while debugging
+* is active.
*/
-#define DMI_ABSTRACTCS_CMDERR_OFFSET 5
-#define DMI_ABSTRACTCS_CMDERR_LENGTH 3
-#define DMI_ABSTRACTCS_CMDERR (0x7 << DMI_ABSTRACTCS_CMDERR_OFFSET)
+#define DMI_DMCONTROL_DMACTIVE_OFFSET 9
+#define DMI_DMCONTROL_DMACTIVE_LENGTH 1
+#define DMI_DMCONTROL_DMACTIVE (0x1 << DMI_DMCONTROL_DMACTIVE_OFFSET)
/*
-* 1: An abstract command is currently being executed.
+* This bit controls the reset signal from the DM to the rest of the
+* system. To perform a reset the debugger writes 1, and then writes 0
+* to deassert the reset.
+ */
+#define DMI_DMCONTROL_RESET_OFFSET 8
+#define DMI_DMCONTROL_RESET_LENGTH 1
+#define DMI_DMCONTROL_RESET (0x1 << DMI_DMCONTROL_RESET_OFFSET)
+/*
+* 0 when authentication is required before using the DM. 1 when the
+* authentication check has passed. On components that don't implement
+* authentication, this bit must be preset as 1.
+ */
+#define DMI_DMCONTROL_AUTHENTICATED_OFFSET 7
+#define DMI_DMCONTROL_AUTHENTICATED_LENGTH 1
+#define DMI_DMCONTROL_AUTHENTICATED (0x1 << DMI_DMCONTROL_AUTHENTICATED_OFFSET)
+/*
+* 0: The authentication module is ready to process the next
+* read/write to \Rauthdata.
*
-* This bit is set as soon as \Rcommand is written, and isn't cleared
-* until that command has completed.
+* 1: The authentication module is busy. Accessing \Rauthdata results
+* in unspecified behavior.
+*
+* \Fauthbusy only becomes set in immediate response to an access to
+* \Rauthdata.
*/
-#define DMI_ABSTRACTCS_BUSY_OFFSET 4
-#define DMI_ABSTRACTCS_BUSY_LENGTH 1
-#define DMI_ABSTRACTCS_BUSY (0x1 << DMI_ABSTRACTCS_BUSY_OFFSET)
+#define DMI_DMCONTROL_AUTHBUSY_OFFSET 6
+#define DMI_DMCONTROL_AUTHBUSY_LENGTH 1
+#define DMI_DMCONTROL_AUTHBUSY (0x1 << DMI_DMCONTROL_AUTHBUSY_OFFSET)
/*
-* Number of {\tt data} registers that are implemented as part of the
-* abstract command interface. If it's 0 then no abstract interface is
-* implemented at all.
+* 0: There is no Debug Module present.
+*
+* 1: There is a Debug Module and it conforms to version 0.12 of this
+* specification.
+*
+* Other values are reserved for future use.
*/
-#define DMI_ABSTRACTCS_DATACOUNT_OFFSET 0
-#define DMI_ABSTRACTCS_DATACOUNT_LENGTH 4
-#define DMI_ABSTRACTCS_DATACOUNT (0xf << DMI_ABSTRACTCS_DATACOUNT_OFFSET)
-#define DMI_COMMAND 0x0f
-#define DMI_COMMAND_COMMAND_OFFSET 0
-#define DMI_COMMAND_COMMAND_LENGTH 32
-#define DMI_COMMAND_COMMAND (0xffffffff << DMI_COMMAND_COMMAND_OFFSET)
-#define DMI_DATA0 0x10
-#define DMI_DATA0_DATA_OFFSET 0
-#define DMI_DATA0_DATA_LENGTH 32
-#define DMI_DATA0_DATA (0xffffffff << DMI_DATA0_DATA_OFFSET)
-#define DMI_DATA1 0x11
-#define DMI_DATA2 0x12
-#define DMI_DATA3 0x13
-#define DMI_DATA4 0x14
-#define DMI_DATA5 0x15
-#define DMI_DATA6 0x16
-#define DMI_DATA7 0x17
-#define DMI_DATA8 0x18
-#define DMI_DATA9 0x19
-#define DMI_DATA10 0x1a
-#define DMI_DATA11 0x1b
-#define DMI_SERDATA 0x1c
-#define DMI_SERDATA_DATA_OFFSET 0
-#define DMI_SERDATA_DATA_LENGTH 32
-#define DMI_SERDATA_DATA (0xffffffff << DMI_SERDATA_DATA_OFFSET)
-#define DMI_SERSTATUS 0x1d
-/*
-* Number of supported serial ports.
- */
-#define DMI_SERSTATUS_SERIALCOUNT_OFFSET 28
-#define DMI_SERSTATUS_SERIALCOUNT_LENGTH 4
-#define DMI_SERSTATUS_SERIALCOUNT (0xf << DMI_SERSTATUS_SERIALCOUNT_OFFSET)
-/*
-* Select which serial port is accessed by \Rserdata.
- */
-#define DMI_SERSTATUS_SERIAL_OFFSET 16
-#define DMI_SERSTATUS_SERIAL_LENGTH 3
-#define DMI_SERSTATUS_SERIAL (0x7 << DMI_SERSTATUS_SERIAL_OFFSET)
-#define DMI_SERSTATUS_VALID7_OFFSET 15
-#define DMI_SERSTATUS_VALID7_LENGTH 1
-#define DMI_SERSTATUS_VALID7 (0x1 << DMI_SERSTATUS_VALID7_OFFSET)
-#define DMI_SERSTATUS_FULL_OVERFLOW7_OFFSET 14
-#define DMI_SERSTATUS_FULL_OVERFLOW7_LENGTH 1
-#define DMI_SERSTATUS_FULL_OVERFLOW7 (0x1 << DMI_SERSTATUS_FULL_OVERFLOW7_OFFSET)
-#define DMI_SERSTATUS_VALID6_OFFSET 13
-#define DMI_SERSTATUS_VALID6_LENGTH 1
-#define DMI_SERSTATUS_VALID6 (0x1 << DMI_SERSTATUS_VALID6_OFFSET)
-#define DMI_SERSTATUS_FULL_OVERFLOW6_OFFSET 12
-#define DMI_SERSTATUS_FULL_OVERFLOW6_LENGTH 1
-#define DMI_SERSTATUS_FULL_OVERFLOW6 (0x1 << DMI_SERSTATUS_FULL_OVERFLOW6_OFFSET)
-#define DMI_SERSTATUS_VALID5_OFFSET 11
-#define DMI_SERSTATUS_VALID5_LENGTH 1
-#define DMI_SERSTATUS_VALID5 (0x1 << DMI_SERSTATUS_VALID5_OFFSET)
-#define DMI_SERSTATUS_FULL_OVERFLOW5_OFFSET 10
-#define DMI_SERSTATUS_FULL_OVERFLOW5_LENGTH 1
-#define DMI_SERSTATUS_FULL_OVERFLOW5 (0x1 << DMI_SERSTATUS_FULL_OVERFLOW5_OFFSET)
-#define DMI_SERSTATUS_VALID4_OFFSET 9
-#define DMI_SERSTATUS_VALID4_LENGTH 1
-#define DMI_SERSTATUS_VALID4 (0x1 << DMI_SERSTATUS_VALID4_OFFSET)
-#define DMI_SERSTATUS_FULL_OVERFLOW4_OFFSET 8
-#define DMI_SERSTATUS_FULL_OVERFLOW4_LENGTH 1
-#define DMI_SERSTATUS_FULL_OVERFLOW4 (0x1 << DMI_SERSTATUS_FULL_OVERFLOW4_OFFSET)
-#define DMI_SERSTATUS_VALID3_OFFSET 7
-#define DMI_SERSTATUS_VALID3_LENGTH 1
-#define DMI_SERSTATUS_VALID3 (0x1 << DMI_SERSTATUS_VALID3_OFFSET)
-#define DMI_SERSTATUS_FULL_OVERFLOW3_OFFSET 6
-#define DMI_SERSTATUS_FULL_OVERFLOW3_LENGTH 1
-#define DMI_SERSTATUS_FULL_OVERFLOW3 (0x1 << DMI_SERSTATUS_FULL_OVERFLOW3_OFFSET)
-#define DMI_SERSTATUS_VALID2_OFFSET 5
-#define DMI_SERSTATUS_VALID2_LENGTH 1
-#define DMI_SERSTATUS_VALID2 (0x1 << DMI_SERSTATUS_VALID2_OFFSET)
-#define DMI_SERSTATUS_FULL_OVERFLOW2_OFFSET 4
-#define DMI_SERSTATUS_FULL_OVERFLOW2_LENGTH 1
-#define DMI_SERSTATUS_FULL_OVERFLOW2 (0x1 << DMI_SERSTATUS_FULL_OVERFLOW2_OFFSET)
-#define DMI_SERSTATUS_VALID1_OFFSET 3
-#define DMI_SERSTATUS_VALID1_LENGTH 1
-#define DMI_SERSTATUS_VALID1 (0x1 << DMI_SERSTATUS_VALID1_OFFSET)
-#define DMI_SERSTATUS_FULL_OVERFLOW1_OFFSET 2
-#define DMI_SERSTATUS_FULL_OVERFLOW1_LENGTH 1
-#define DMI_SERSTATUS_FULL_OVERFLOW1 (0x1 << DMI_SERSTATUS_FULL_OVERFLOW1_OFFSET)
-/*
-* 1 when the core-to-debugger queue for serial port 0 is not empty.
- */
-#define DMI_SERSTATUS_VALID0_OFFSET 1
-#define DMI_SERSTATUS_VALID0_LENGTH 1
-#define DMI_SERSTATUS_VALID0 (0x1 << DMI_SERSTATUS_VALID0_OFFSET)
-/*
-* 1 when the debugger-to-core queue for serial port 0 is either full,
-* or has overflowed. Overflow state is sticky, and can be reset by
-* writing 0 to this bit.
- */
-#define DMI_SERSTATUS_FULL_OVERFLOW0_OFFSET 0
-#define DMI_SERSTATUS_FULL_OVERFLOW0_LENGTH 1
-#define DMI_SERSTATUS_FULL_OVERFLOW0 (0x1 << DMI_SERSTATUS_FULL_OVERFLOW0_OFFSET)
-#define DMI_ACCESSCS 0x1f
-/*
-* Size of the Program Buffer, in 32-bit words. Valid sizes are 0 - 12.
-*
-* A debugger must not access any Instruction Buffer locations that
-* fall outside the range specified here.
-*
-* TODO: Explain what can be done with each size of the buffer, to suggest
-* why you would want more or less words.
- */
-#define DMI_ACCESSCS_PROGSIZE_OFFSET 0
-#define DMI_ACCESSCS_PROGSIZE_LENGTH 4
-#define DMI_ACCESSCS_PROGSIZE (0xf << DMI_ACCESSCS_PROGSIZE_OFFSET)
-#define DMI_IBUF0 0x20
-#define DMI_IBUF0_DATA_OFFSET 0
-#define DMI_IBUF0_DATA_LENGTH 32
-#define DMI_IBUF0_DATA (0xffffffff << DMI_IBUF0_DATA_OFFSET)
-#define DMI_IBUF1 0x21
-#define DMI_IBUF2 0x22
-#define DMI_IBUF3 0x23
-#define DMI_IBUF4 0x24
-#define DMI_IBUF5 0x25
-#define DMI_IBUF6 0x26
-#define DMI_IBUF7 0x27
-#define DMI_IBUF8 0x28
-#define DMI_IBUF9 0x29
-#define DMI_IBUF10 0x2a
-#define DMI_IBUF11 0x2b
-#define SERINFO 0x110
-/*
-* Like \Fserialzero.
- */
-#define SERINFO_SERIAL7_OFFSET 7
-#define SERINFO_SERIAL7_LENGTH 1
-#define SERINFO_SERIAL7 (0x1 << SERINFO_SERIAL7_OFFSET)
-/*
-* Like \Fserialzero.
- */
-#define SERINFO_SERIAL6_OFFSET 6
-#define SERINFO_SERIAL6_LENGTH 1
-#define SERINFO_SERIAL6 (0x1 << SERINFO_SERIAL6_OFFSET)
-/*
-* Like \Fserialzero.
- */
-#define SERINFO_SERIAL5_OFFSET 5
-#define SERINFO_SERIAL5_LENGTH 1
-#define SERINFO_SERIAL5 (0x1 << SERINFO_SERIAL5_OFFSET)
-/*
-* Like \Fserialzero.
- */
-#define SERINFO_SERIAL4_OFFSET 4
-#define SERINFO_SERIAL4_LENGTH 1
-#define SERINFO_SERIAL4 (0x1 << SERINFO_SERIAL4_OFFSET)
-/*
-* Like \Fserialzero.
- */
-#define SERINFO_SERIAL3_OFFSET 3
-#define SERINFO_SERIAL3_LENGTH 1
-#define SERINFO_SERIAL3 (0x1 << SERINFO_SERIAL3_OFFSET)
-/*
-* Like \Fserialzero.
- */
-#define SERINFO_SERIAL2_OFFSET 2
-#define SERINFO_SERIAL2_LENGTH 1
-#define SERINFO_SERIAL2 (0x1 << SERINFO_SERIAL2_OFFSET)
-/*
-* Like \Fserialzero.
- */
-#define SERINFO_SERIAL1_OFFSET 1
-#define SERINFO_SERIAL1_LENGTH 1
-#define SERINFO_SERIAL1 (0x1 << SERINFO_SERIAL1_OFFSET)
-/*
-* 1 means serial interface 0 is supported.
- */
-#define SERINFO_SERIAL0_OFFSET 0
-#define SERINFO_SERIAL0_LENGTH 1
-#define SERINFO_SERIAL0 (0x1 << SERINFO_SERIAL0_OFFSET)
-#define SERSEND0 0x200
-#define SERRECV0 0x204
-#define SERSTAT0 0x208
-/*
-* Send ready. 1 when the core-to-debugger queue is not full. 0
-* otherwise.
- */
-#define SERSTAT0_SENDR_OFFSET 1
-#define SERSTAT0_SENDR_LENGTH 1
-#define SERSTAT0_SENDR (0x1 << SERSTAT0_SENDR_OFFSET)
-/*
-* Receive ready. 1 when the debugger-to-core queue is not empty. 0
-* otherwise.
- */
-#define SERSTAT0_RECVR_OFFSET 0
-#define SERSTAT0_RECVR_LENGTH 1
-#define SERSTAT0_RECVR (0x1 << SERSTAT0_RECVR_OFFSET)
-#define SERSEND1 0x20c
-#define SERRECV1 0x210
-#define SERSTAT1 0x214
-#define SERSEND2 0x218
-#define SERRECV2 0x21c
-#define SERSTAT2 0x220
-#define SERSEND3 0x224
-#define SERRECV3 0x228
-#define SERSTAT3 0x22c
-#define SERSEND4 0x230
-#define SERRECV4 0x234
-#define SERSTAT4 0x238
-#define SERSEND5 0x23c
-#define SERRECV5 0x240
-#define SERSTAT5 0x244
-#define SERSEND6 0x248
-#define SERRECV6 0x24c
-#define SERSTAT6 0x250
-#define SERSEND7 0x254
-#define SERRECV7 0x258
-#define SERSTAT7 0x25c
-#define CSR_TSELECT 0x7a0
-#define CSR_TSELECT_INDEX_OFFSET 0
-#define CSR_TSELECT_INDEX_LENGTH XLEN
-#define CSR_TSELECT_INDEX (((1L<<XLEN)-1) << CSR_TSELECT_INDEX_OFFSET)
-#define CSR_TDATA1 0x7a1
+#define DMI_DMCONTROL_VERSION_OFFSET 0
+#define DMI_DMCONTROL_VERSION_LENGTH 4
+#define DMI_DMCONTROL_VERSION (0xf << DMI_DMCONTROL_VERSION_OFFSET)
+#define DMI_HARTINFO 0x01
/*
-* 0: There is no trigger at this \Rtselect.
-*
-* 1: The trigger is a legacy SiFive address match trigger. These
-* should not be implemented and aren't further documented here.
-*
-* 2: The trigger is an address/data match trigger.
-*
-* 3: The trigger is an instruction count trigger.
-*
-* 15: This trigger exists (so enumeration shouldn't terminate), but
-* is not currently available.
+* 0: The {\tt data} registers are shadowed in the hart by CSR
+* registers. Each CSR register is XLEN bits in size, and corresponds
+* to a single argument, per Table~\ref{tab:datareg}.
*
-* Other values are reserved for future use.
+* 1: The {\tt data} registers are shadowed in the hart's memory map.
+* Each register takes up 4 bytes in the memory map.
*/
-#define CSR_TDATA1_TYPE_OFFSET XLEN-4
-#define CSR_TDATA1_TYPE_LENGTH 4
-#define CSR_TDATA1_TYPE (0xfL << CSR_TDATA1_TYPE_OFFSET)
+#define DMI_HARTINFO_DATAACCESS_OFFSET 16
+#define DMI_HARTINFO_DATAACCESS_LENGTH 1
+#define DMI_HARTINFO_DATAACCESS (0x1 << DMI_HARTINFO_DATAACCESS_OFFSET)
/*
-* 0: Both Debug and M Mode can write the {\tt tdata} registers at the
-* selected \Rtselect.
-*
-* 1: Only Debug Mode can write the {\tt tdata} registers at the
-* selected \Rtselect. Writes from other modes are ignored.
+* If \Fdataaccess is 0: Number of CSR registers dedicated to
+* shadowing the {\tt data} registers.
*
-* This bit is only writable from Debug Mode.
- */
-#define CSR_TDATA1_DMODE_OFFSET XLEN-5
-#define CSR_TDATA1_DMODE_LENGTH 1
-#define CSR_TDATA1_DMODE (0x1L << CSR_TDATA1_DMODE_OFFSET)
-/*
-* Trigger-specific data.
- */
-#define CSR_TDATA1_DATA_OFFSET 0
-#define CSR_TDATA1_DATA_LENGTH XLEN - 5
-#define CSR_TDATA1_DATA (((1L<<XLEN - 5)-1) << CSR_TDATA1_DATA_OFFSET)
-#define CSR_TDATA2 0x7a2
-#define CSR_TDATA2_DATA_OFFSET 0
-#define CSR_TDATA2_DATA_LENGTH XLEN
-#define CSR_TDATA2_DATA (((1L<<XLEN)-1) << CSR_TDATA2_DATA_OFFSET)
-#define CSR_TDATA3 0x7a3
-#define CSR_TDATA3_DATA_OFFSET 0
-#define CSR_TDATA3_DATA_LENGTH XLEN
-#define CSR_TDATA3_DATA (((1L<<XLEN)-1) << CSR_TDATA3_DATA_OFFSET)
-#define CSR_MCONTROL 0x7a1
-#define CSR_MCONTROL_TYPE_OFFSET XLEN-4
-#define CSR_MCONTROL_TYPE_LENGTH 4
-#define CSR_MCONTROL_TYPE (0xfL << CSR_MCONTROL_TYPE_OFFSET)
-#define CSR_MCONTROL_DMODE_OFFSET XLEN-5
-#define CSR_MCONTROL_DMODE_LENGTH 1
-#define CSR_MCONTROL_DMODE (0x1L << CSR_MCONTROL_DMODE_OFFSET)
-/*
-* Specifies the largest naturally aligned powers-of-two (NAPOT) range
-* supported by the hardware. The value is the logarithm base 2 of the
-* number of bytes in that range. A value of 0 indicates that only
-* exact value matches are supported (one byte range). A value of 63
-* corresponds to the maximum NAPOT range, which is $2^{63}$ bytes in
-* size.
+* If \Fdataaccess is 1: Number of 32-bit words in the memory map
+* dedicated to shadowing the {\tt data} registers.
*/
-#define CSR_MCONTROL_MASKMAX_OFFSET XLEN-11
-#define CSR_MCONTROL_MASKMAX_LENGTH 6
-#define CSR_MCONTROL_MASKMAX (0x3fL << CSR_MCONTROL_MASKMAX_OFFSET)
+#define DMI_HARTINFO_DATASIZE_OFFSET 12
+#define DMI_HARTINFO_DATASIZE_LENGTH 4
+#define DMI_HARTINFO_DATASIZE (0xf << DMI_HARTINFO_DATASIZE_OFFSET)
/*
-* 0: Perform a match on the address.
+* If \Fdataaccess is 0: The number of the first CSR dedicated to
+* shadowing the {\tt data} registers.
*
-* 1: Perform a match on the data value loaded/stored, or the
-* instruction executed.
+* If \Fdataaccess is 1: Signed address of RAM where the {\tt data}
+* registers are shadowed.
*/
-#define CSR_MCONTROL_SELECT_OFFSET 19
-#define CSR_MCONTROL_SELECT_LENGTH 1
-#define CSR_MCONTROL_SELECT (0x1L << CSR_MCONTROL_SELECT_OFFSET)
+#define DMI_HARTINFO_DATAADDR_OFFSET 0
+#define DMI_HARTINFO_DATAADDR_LENGTH 12
+#define DMI_HARTINFO_DATAADDR (0xfff << DMI_HARTINFO_DATAADDR_OFFSET)
+#define DMI_HALTSUM 0x02
+#define DMI_HALTSUM_HALT1023_992_OFFSET 31
+#define DMI_HALTSUM_HALT1023_992_LENGTH 1
+#define DMI_HALTSUM_HALT1023_992 (0x1 << DMI_HALTSUM_HALT1023_992_OFFSET)
+#define DMI_HALTSUM_HALT991_960_OFFSET 30
+#define DMI_HALTSUM_HALT991_960_LENGTH 1
+#define DMI_HALTSUM_HALT991_960 (0x1 << DMI_HALTSUM_HALT991_960_OFFSET)
+#define DMI_HALTSUM_HALT959_928_OFFSET 29
+#define DMI_HALTSUM_HALT959_928_LENGTH 1
+#define DMI_HALTSUM_HALT959_928 (0x1 << DMI_HALTSUM_HALT959_928_OFFSET)
+#define DMI_HALTSUM_HALT927_896_OFFSET 28
+#define DMI_HALTSUM_HALT927_896_LENGTH 1
+#define DMI_HALTSUM_HALT927_896 (0x1 << DMI_HALTSUM_HALT927_896_OFFSET)
+#define DMI_HALTSUM_HALT895_864_OFFSET 27
+#define DMI_HALTSUM_HALT895_864_LENGTH 1
+#define DMI_HALTSUM_HALT895_864 (0x1 << DMI_HALTSUM_HALT895_864_OFFSET)
+#define DMI_HALTSUM_HALT863_832_OFFSET 26
+#define DMI_HALTSUM_HALT863_832_LENGTH 1
+#define DMI_HALTSUM_HALT863_832 (0x1 << DMI_HALTSUM_HALT863_832_OFFSET)
+#define DMI_HALTSUM_HALT831_800_OFFSET 25
+#define DMI_HALTSUM_HALT831_800_LENGTH 1
+#define DMI_HALTSUM_HALT831_800 (0x1 << DMI_HALTSUM_HALT831_800_OFFSET)
+#define DMI_HALTSUM_HALT799_768_OFFSET 24
+#define DMI_HALTSUM_HALT799_768_LENGTH 1
+#define DMI_HALTSUM_HALT799_768 (0x1 << DMI_HALTSUM_HALT799_768_OFFSET)
+#define DMI_HALTSUM_HALT767_736_OFFSET 23
+#define DMI_HALTSUM_HALT767_736_LENGTH 1
+#define DMI_HALTSUM_HALT767_736 (0x1 << DMI_HALTSUM_HALT767_736_OFFSET)
+#define DMI_HALTSUM_HALT735_704_OFFSET 22
+#define DMI_HALTSUM_HALT735_704_LENGTH 1
+#define DMI_HALTSUM_HALT735_704 (0x1 << DMI_HALTSUM_HALT735_704_OFFSET)
+#define DMI_HALTSUM_HALT703_672_OFFSET 21
+#define DMI_HALTSUM_HALT703_672_LENGTH 1
+#define DMI_HALTSUM_HALT703_672 (0x1 << DMI_HALTSUM_HALT703_672_OFFSET)
+#define DMI_HALTSUM_HALT671_640_OFFSET 20
+#define DMI_HALTSUM_HALT671_640_LENGTH 1
+#define DMI_HALTSUM_HALT671_640 (0x1 << DMI_HALTSUM_HALT671_640_OFFSET)
+#define DMI_HALTSUM_HALT639_608_OFFSET 19
+#define DMI_HALTSUM_HALT639_608_LENGTH 1
+#define DMI_HALTSUM_HALT639_608 (0x1 << DMI_HALTSUM_HALT639_608_OFFSET)
+#define DMI_HALTSUM_HALT607_576_OFFSET 18
+#define DMI_HALTSUM_HALT607_576_LENGTH 1
+#define DMI_HALTSUM_HALT607_576 (0x1 << DMI_HALTSUM_HALT607_576_OFFSET)
+#define DMI_HALTSUM_HALT575_544_OFFSET 17
+#define DMI_HALTSUM_HALT575_544_LENGTH 1
+#define DMI_HALTSUM_HALT575_544 (0x1 << DMI_HALTSUM_HALT575_544_OFFSET)
+#define DMI_HALTSUM_HALT543_512_OFFSET 16
+#define DMI_HALTSUM_HALT543_512_LENGTH 1
+#define DMI_HALTSUM_HALT543_512 (0x1 << DMI_HALTSUM_HALT543_512_OFFSET)
+#define DMI_HALTSUM_HALT511_480_OFFSET 15
+#define DMI_HALTSUM_HALT511_480_LENGTH 1
+#define DMI_HALTSUM_HALT511_480 (0x1 << DMI_HALTSUM_HALT511_480_OFFSET)
+#define DMI_HALTSUM_HALT479_448_OFFSET 14
+#define DMI_HALTSUM_HALT479_448_LENGTH 1
+#define DMI_HALTSUM_HALT479_448 (0x1 << DMI_HALTSUM_HALT479_448_OFFSET)
+#define DMI_HALTSUM_HALT447_416_OFFSET 13
+#define DMI_HALTSUM_HALT447_416_LENGTH 1
+#define DMI_HALTSUM_HALT447_416 (0x1 << DMI_HALTSUM_HALT447_416_OFFSET)
+#define DMI_HALTSUM_HALT415_384_OFFSET 12
+#define DMI_HALTSUM_HALT415_384_LENGTH 1
+#define DMI_HALTSUM_HALT415_384 (0x1 << DMI_HALTSUM_HALT415_384_OFFSET)
+#define DMI_HALTSUM_HALT383_352_OFFSET 11
+#define DMI_HALTSUM_HALT383_352_LENGTH 1
+#define DMI_HALTSUM_HALT383_352 (0x1 << DMI_HALTSUM_HALT383_352_OFFSET)
+#define DMI_HALTSUM_HALT351_320_OFFSET 10
+#define DMI_HALTSUM_HALT351_320_LENGTH 1
+#define DMI_HALTSUM_HALT351_320 (0x1 << DMI_HALTSUM_HALT351_320_OFFSET)
+#define DMI_HALTSUM_HALT319_288_OFFSET 9
+#define DMI_HALTSUM_HALT319_288_LENGTH 1
+#define DMI_HALTSUM_HALT319_288 (0x1 << DMI_HALTSUM_HALT319_288_OFFSET)
+#define DMI_HALTSUM_HALT287_256_OFFSET 8
+#define DMI_HALTSUM_HALT287_256_LENGTH 1
+#define DMI_HALTSUM_HALT287_256 (0x1 << DMI_HALTSUM_HALT287_256_OFFSET)
+#define DMI_HALTSUM_HALT255_224_OFFSET 7
+#define DMI_HALTSUM_HALT255_224_LENGTH 1
+#define DMI_HALTSUM_HALT255_224 (0x1 << DMI_HALTSUM_HALT255_224_OFFSET)
+#define DMI_HALTSUM_HALT223_192_OFFSET 6
+#define DMI_HALTSUM_HALT223_192_LENGTH 1
+#define DMI_HALTSUM_HALT223_192 (0x1 << DMI_HALTSUM_HALT223_192_OFFSET)
+#define DMI_HALTSUM_HALT191_160_OFFSET 5
+#define DMI_HALTSUM_HALT191_160_LENGTH 1
+#define DMI_HALTSUM_HALT191_160 (0x1 << DMI_HALTSUM_HALT191_160_OFFSET)
+#define DMI_HALTSUM_HALT159_128_OFFSET 4
+#define DMI_HALTSUM_HALT159_128_LENGTH 1
+#define DMI_HALTSUM_HALT159_128 (0x1 << DMI_HALTSUM_HALT159_128_OFFSET)
+#define DMI_HALTSUM_HALT127_96_OFFSET 3
+#define DMI_HALTSUM_HALT127_96_LENGTH 1
+#define DMI_HALTSUM_HALT127_96 (0x1 << DMI_HALTSUM_HALT127_96_OFFSET)
+#define DMI_HALTSUM_HALT95_64_OFFSET 2
+#define DMI_HALTSUM_HALT95_64_LENGTH 1
+#define DMI_HALTSUM_HALT95_64 (0x1 << DMI_HALTSUM_HALT95_64_OFFSET)
+#define DMI_HALTSUM_HALT63_32_OFFSET 1
+#define DMI_HALTSUM_HALT63_32_LENGTH 1
+#define DMI_HALTSUM_HALT63_32 (0x1 << DMI_HALTSUM_HALT63_32_OFFSET)
+#define DMI_HALTSUM_HALT31_0_OFFSET 0
+#define DMI_HALTSUM_HALT31_0_LENGTH 1
+#define DMI_HALTSUM_HALT31_0 (0x1 << DMI_HALTSUM_HALT31_0_OFFSET)
+#define DMI_SBCS 0x03
/*
-* 0: The action for this trigger will be taken just before the
-* instruction that triggered it is executed, but after all preceding
-* instructions are are committed.
-*
-* 1: The action for this trigger will be taken after the instruction
-* that triggered it is executed. It should be taken before the next
-* instruction is executed, but it is better to implement triggers and
-* not implement that suggestion than to not implement them at all.
-*
-* Most hardware will only implement one timing or the other, possibly
-* dependent on \Fselect, \Fexecute, \Fload, and \Fstore. This bit
-* primarily exists for the hardware to communicate to the debugger
-* what will happen. Hardware may implement the bit fully writable, in
-* which case the debugger has a little more control.
-*
-* Data load triggers with \Ftiming of 0 will result in the same load
-* happening again when the debugger lets the core run. For data load
-* triggers debuggers must first attempt to set the breakpoint with
-* \Ftiming of 1.
-*
-* A chain of triggers that don't all have the same \Ftiming value
-* will never fire (unless consecutive instructions match the
-* appropriate triggers).
+* When a 1 is written here, triggers a read at the address in {\tt
+* sbaddress} using the access size set by \Fsbaccess.
*/
-#define CSR_MCONTROL_TIMING_OFFSET 18
-#define CSR_MCONTROL_TIMING_LENGTH 1
-#define CSR_MCONTROL_TIMING (0x1L << CSR_MCONTROL_TIMING_OFFSET)
+#define DMI_SBCS_SBSINGLEREAD_OFFSET 20
+#define DMI_SBCS_SBSINGLEREAD_LENGTH 1
+#define DMI_SBCS_SBSINGLEREAD (0x1 << DMI_SBCS_SBSINGLEREAD_OFFSET)
/*
-* Determines what happens when this trigger matches.
+* Select the access size to use for system bus accesses triggered by
+* writes to the {\tt sbaddress} registers or \Rsbdatazero.
*
-* 0: Raise a breakpoint exception. (Used when software wants to use
-* the trigger module without an external debugger attached.)
+* 0: 8-bit
*
-* 1: Enter Debug Mode. (Only supported when \Fdmode is 1.)
+* 1: 16-bit
*
-* 2: Start tracing.
+* 2: 32-bit
*
-* 3: Stop tracing.
+* 3: 64-bit
*
-* 4: Emit trace data for this match. If it is a data access match,
-* emit appropriate Load/Store Address/Data. If it is an instruction
-* execution, emit its PC.
+* 4: 128-bit
*
-* Other values are reserved for future use.
+* If an unsupported system bus access size is written here,
+* the DM may not
+* perform the access, or may perform the access with any access size
*/
-#define CSR_MCONTROL_ACTION_OFFSET 12
-#define CSR_MCONTROL_ACTION_LENGTH 6
-#define CSR_MCONTROL_ACTION (0x3fL << CSR_MCONTROL_ACTION_OFFSET)
+#define DMI_SBCS_SBACCESS_OFFSET 17
+#define DMI_SBCS_SBACCESS_LENGTH 3
+#define DMI_SBCS_SBACCESS (0x7 << DMI_SBCS_SBACCESS_OFFSET)
/*
-* 0: When this trigger matches, the configured action is taken.
-*
-* 1: While this trigger does not match, it prevents the trigger with
-* the next index from matching.
+* When 1, the internal address value (used by the system bus master)
+* is incremented by the access size (in bytes) selected in \Fsbaccess
+* after every system bus access.
+ */
+#define DMI_SBCS_SBAUTOINCREMENT_OFFSET 16
+#define DMI_SBCS_SBAUTOINCREMENT_LENGTH 1
+#define DMI_SBCS_SBAUTOINCREMENT (0x1 << DMI_SBCS_SBAUTOINCREMENT_OFFSET)
+/*
+* When 1, every read from \Rsbdatazero automatically triggers a system
+* bus read at the new address.
*/
-#define CSR_MCONTROL_CHAIN_OFFSET 11
-#define CSR_MCONTROL_CHAIN_LENGTH 1
-#define CSR_MCONTROL_CHAIN (0x1L << CSR_MCONTROL_CHAIN_OFFSET)
+#define DMI_SBCS_SBAUTOREAD_OFFSET 15
+#define DMI_SBCS_SBAUTOREAD_LENGTH 1
+#define DMI_SBCS_SBAUTOREAD (0x1 << DMI_SBCS_SBAUTOREAD_OFFSET)
/*
-* 0: Matches when the value equals \Rtdatatwo.
-*
-* 1: Matches when the top M bits of the value match the top M bits of
-* \Rtdatatwo. M is XLEN-1 minus the index of the least-significant
-* bit containing 0 in \Rtdatatwo.
+* When the debug module's system bus
+* master causes a bus error, this field gets set.
+* It remains set until 0 is written to any bit in this field. Until
+* that happens, the system bus master is busy and no more accesses can be
+* initiated by the debug module.
*
-* 2: Matches when the value is greater than or equal to \Rtdatatwo.
+* 0: There was no bus error.
*
-* 3: Matches when the value is less than \Rtdatatwo.
+* 1: There was a timeout.
*
-* 4: Matches when the lower half of the value equals the lower half
-* of \Rtdatatwo after the lower half of the value is ANDed with the
-* upper half of \Rtdatatwo.
+* 2: A bad address was accessed.
*
-* 5: Matches when the upper half of the value equals the lower half
-* of \Rtdatatwo after the upper half of the value is ANDed with the
-* upper half of \Rtdatatwo.
+* 3: There was some other error (eg. alignment).
*
-* Other values are reserved for future use.
+* 4: The system bus master was busy when a one of the
+* {\tt sbaddress} or {\tt sbdata} registers was written,
+* or the {\tt sbdata} register was read when it had
+* stale data.
*/
-#define CSR_MCONTROL_MATCH_OFFSET 7
-#define CSR_MCONTROL_MATCH_LENGTH 4
-#define CSR_MCONTROL_MATCH (0xfL << CSR_MCONTROL_MATCH_OFFSET)
+#define DMI_SBCS_SBERROR_OFFSET 12
+#define DMI_SBCS_SBERROR_LENGTH 3
+#define DMI_SBCS_SBERROR (0x7 << DMI_SBCS_SBERROR_OFFSET)
/*
-* When set, enable this trigger in M mode.
+* Width of system bus addresses in bits. (0 indicates there is no bus
+* access support.)
*/
-#define CSR_MCONTROL_M_OFFSET 6
-#define CSR_MCONTROL_M_LENGTH 1
-#define CSR_MCONTROL_M (0x1L << CSR_MCONTROL_M_OFFSET)
+#define DMI_SBCS_SBASIZE_OFFSET 5
+#define DMI_SBCS_SBASIZE_LENGTH 7
+#define DMI_SBCS_SBASIZE (0x7f << DMI_SBCS_SBASIZE_OFFSET)
/*
-* When set, enable this trigger in H mode.
+* 1 when 128-bit system bus accesses are supported.
*/
-#define CSR_MCONTROL_H_OFFSET 5
-#define CSR_MCONTROL_H_LENGTH 1
-#define CSR_MCONTROL_H (0x1L << CSR_MCONTROL_H_OFFSET)
+#define DMI_SBCS_SBACCESS128_OFFSET 4
+#define DMI_SBCS_SBACCESS128_LENGTH 1
+#define DMI_SBCS_SBACCESS128 (0x1 << DMI_SBCS_SBACCESS128_OFFSET)
/*
-* When set, enable this trigger in S mode.
+* 1 when 64-bit system bus accesses are supported.
*/
-#define CSR_MCONTROL_S_OFFSET 4
-#define CSR_MCONTROL_S_LENGTH 1
-#define CSR_MCONTROL_S (0x1L << CSR_MCONTROL_S_OFFSET)
+#define DMI_SBCS_SBACCESS64_OFFSET 3
+#define DMI_SBCS_SBACCESS64_LENGTH 1
+#define DMI_SBCS_SBACCESS64 (0x1 << DMI_SBCS_SBACCESS64_OFFSET)
/*
-* When set, enable this trigger in U mode.
+* 1 when 32-bit system bus accesses are supported.
*/
-#define CSR_MCONTROL_U_OFFSET 3
-#define CSR_MCONTROL_U_LENGTH 1
-#define CSR_MCONTROL_U (0x1L << CSR_MCONTROL_U_OFFSET)
+#define DMI_SBCS_SBACCESS32_OFFSET 2
+#define DMI_SBCS_SBACCESS32_LENGTH 1
+#define DMI_SBCS_SBACCESS32 (0x1 << DMI_SBCS_SBACCESS32_OFFSET)
/*
-* When set, the trigger fires on the address or opcode of an
-* instruction that is executed.
+* 1 when 16-bit system bus accesses are supported.
*/
-#define CSR_MCONTROL_EXECUTE_OFFSET 2
-#define CSR_MCONTROL_EXECUTE_LENGTH 1
-#define CSR_MCONTROL_EXECUTE (0x1L << CSR_MCONTROL_EXECUTE_OFFSET)
+#define DMI_SBCS_SBACCESS16_OFFSET 1
+#define DMI_SBCS_SBACCESS16_LENGTH 1
+#define DMI_SBCS_SBACCESS16 (0x1 << DMI_SBCS_SBACCESS16_OFFSET)
/*
-* When set, the trigger fires on the address or data of a store.
+* 1 when 8-bit system bus accesses are supported.
*/
-#define CSR_MCONTROL_STORE_OFFSET 1
-#define CSR_MCONTROL_STORE_LENGTH 1
-#define CSR_MCONTROL_STORE (0x1L << CSR_MCONTROL_STORE_OFFSET)
+#define DMI_SBCS_SBACCESS8_OFFSET 0
+#define DMI_SBCS_SBACCESS8_LENGTH 1
+#define DMI_SBCS_SBACCESS8 (0x1 << DMI_SBCS_SBACCESS8_OFFSET)
+#define DMI_SBADDRESS0 0x04
/*
-* When set, the trigger fires on the address or data of a load.
+* Accesses bits 31:0 of the internal address.
*/
-#define CSR_MCONTROL_LOAD_OFFSET 0
-#define CSR_MCONTROL_LOAD_LENGTH 1
-#define CSR_MCONTROL_LOAD (0x1L << CSR_MCONTROL_LOAD_OFFSET)
-#define CSR_ICOUNT 0x7a1
-#define CSR_ICOUNT_TYPE_OFFSET XLEN-4
-#define CSR_ICOUNT_TYPE_LENGTH 4
-#define CSR_ICOUNT_TYPE (0xfL << CSR_ICOUNT_TYPE_OFFSET)
-#define CSR_ICOUNT_DMODE_OFFSET XLEN-5
-#define CSR_ICOUNT_DMODE_LENGTH 1
-#define CSR_ICOUNT_DMODE (0x1L << CSR_ICOUNT_DMODE_OFFSET)
+#define DMI_SBADDRESS0_ADDRESS_OFFSET 0
+#define DMI_SBADDRESS0_ADDRESS_LENGTH 32
+#define DMI_SBADDRESS0_ADDRESS (0xffffffff << DMI_SBADDRESS0_ADDRESS_OFFSET)
+#define DMI_SBADDRESS1 0x05
/*
-* When count is decremented to 0, the trigger fires. Instead of
-* changing \Fcount from 1 to 0, it is also acceptable for hardware to
-* clear \Fm, \Fh, \Fs, and \Fu. This allows \Fcount to be hard-wired
-* to 1 if this register just exists for single step.
+* Accesses bits 63:32 of the internal address (if the system address
+* bus is that wide).
*/
-#define CSR_ICOUNT_COUNT_OFFSET 10
-#define CSR_ICOUNT_COUNT_LENGTH 14
-#define CSR_ICOUNT_COUNT (0x3fffL << CSR_ICOUNT_COUNT_OFFSET)
+#define DMI_SBADDRESS1_ADDRESS_OFFSET 0
+#define DMI_SBADDRESS1_ADDRESS_LENGTH 32
+#define DMI_SBADDRESS1_ADDRESS (0xffffffff << DMI_SBADDRESS1_ADDRESS_OFFSET)
+#define DMI_SBADDRESS2 0x06
/*
-* When set, every instruction completed in M mode decrements \Fcount
-* by 1.
+* Accesses bits 95:64 of the internal address (if the system address
+* bus is that wide).
*/
-#define CSR_ICOUNT_M_OFFSET 9
-#define CSR_ICOUNT_M_LENGTH 1
-#define CSR_ICOUNT_M (0x1L << CSR_ICOUNT_M_OFFSET)
+#define DMI_SBADDRESS2_ADDRESS_OFFSET 0
+#define DMI_SBADDRESS2_ADDRESS_LENGTH 32
+#define DMI_SBADDRESS2_ADDRESS (0xffffffff << DMI_SBADDRESS2_ADDRESS_OFFSET)
+#define DMI_SBDATA0 0x07
/*
-* When set, every instruction completed in H mode decrements \Fcount
-* by 1.
+* Accesses bits 31:0 of the internal data.
*/
-#define CSR_ICOUNT_H_OFFSET 8
-#define CSR_ICOUNT_H_LENGTH 1
-#define CSR_ICOUNT_H (0x1L << CSR_ICOUNT_H_OFFSET)
+#define DMI_SBDATA0_DATA_OFFSET 0
+#define DMI_SBDATA0_DATA_LENGTH 32
+#define DMI_SBDATA0_DATA (0xffffffff << DMI_SBDATA0_DATA_OFFSET)
+#define DMI_SBDATA1 0x08
/*
-* When set, every instruction completed in S mode decrements \Fcount
-* by 1.
+* Accesses bits 63:32 of the internal data (if the system bus is
+* that wide).
*/
-#define CSR_ICOUNT_S_OFFSET 7
-#define CSR_ICOUNT_S_LENGTH 1
-#define CSR_ICOUNT_S (0x1L << CSR_ICOUNT_S_OFFSET)
+#define DMI_SBDATA1_DATA_OFFSET 0
+#define DMI_SBDATA1_DATA_LENGTH 32
+#define DMI_SBDATA1_DATA (0xffffffff << DMI_SBDATA1_DATA_OFFSET)
+#define DMI_SBDATA2 0x09
/*
-* When set, every instruction completed in U mode decrements \Fcount
-* by 1.
+* Accesses bits 95:64 of the internal data (if the system bus is
+* that wide).
*/
-#define CSR_ICOUNT_U_OFFSET 6
-#define CSR_ICOUNT_U_LENGTH 1
-#define CSR_ICOUNT_U (0x1L << CSR_ICOUNT_U_OFFSET)
+#define DMI_SBDATA2_DATA_OFFSET 0
+#define DMI_SBDATA2_DATA_LENGTH 32
+#define DMI_SBDATA2_DATA (0xffffffff << DMI_SBDATA2_DATA_OFFSET)
+#define DMI_SBDATA3 0x0a
/*
-* Determines what happens when this trigger matches.
+* Accesses bits 127:96 of the internal data (if the system bus is
+* that wide).
+ */
+#define DMI_SBDATA3_DATA_OFFSET 0
+#define DMI_SBDATA3_DATA_LENGTH 32
+#define DMI_SBDATA3_DATA (0xffffffff << DMI_SBDATA3_DATA_OFFSET)
+#define DMI_AUTHDATA 0x0b
+#define DMI_AUTHDATA_DATA_OFFSET 0
+#define DMI_AUTHDATA_DATA_LENGTH 32
+#define DMI_AUTHDATA_DATA (0xffffffff << DMI_AUTHDATA_DATA_OFFSET)
+#define DMI_ABSTRACTCS 0x0e
+#define DMI_ABSTRACTCS_AUTOEXEC7_OFFSET 15
+#define DMI_ABSTRACTCS_AUTOEXEC7_LENGTH 1
+#define DMI_ABSTRACTCS_AUTOEXEC7 (0x1 << DMI_ABSTRACTCS_AUTOEXEC7_OFFSET)
+#define DMI_ABSTRACTCS_AUTOEXEC6_OFFSET 14
+#define DMI_ABSTRACTCS_AUTOEXEC6_LENGTH 1
+#define DMI_ABSTRACTCS_AUTOEXEC6 (0x1 << DMI_ABSTRACTCS_AUTOEXEC6_OFFSET)
+#define DMI_ABSTRACTCS_AUTOEXEC5_OFFSET 13
+#define DMI_ABSTRACTCS_AUTOEXEC5_LENGTH 1
+#define DMI_ABSTRACTCS_AUTOEXEC5 (0x1 << DMI_ABSTRACTCS_AUTOEXEC5_OFFSET)
+#define DMI_ABSTRACTCS_AUTOEXEC4_OFFSET 12
+#define DMI_ABSTRACTCS_AUTOEXEC4_LENGTH 1
+#define DMI_ABSTRACTCS_AUTOEXEC4 (0x1 << DMI_ABSTRACTCS_AUTOEXEC4_OFFSET)
+#define DMI_ABSTRACTCS_AUTOEXEC3_OFFSET 11
+#define DMI_ABSTRACTCS_AUTOEXEC3_LENGTH 1
+#define DMI_ABSTRACTCS_AUTOEXEC3 (0x1 << DMI_ABSTRACTCS_AUTOEXEC3_OFFSET)
+#define DMI_ABSTRACTCS_AUTOEXEC2_OFFSET 10
+#define DMI_ABSTRACTCS_AUTOEXEC2_LENGTH 1
+#define DMI_ABSTRACTCS_AUTOEXEC2 (0x1 << DMI_ABSTRACTCS_AUTOEXEC2_OFFSET)
+#define DMI_ABSTRACTCS_AUTOEXEC1_OFFSET 9
+#define DMI_ABSTRACTCS_AUTOEXEC1_LENGTH 1
+#define DMI_ABSTRACTCS_AUTOEXEC1 (0x1 << DMI_ABSTRACTCS_AUTOEXEC1_OFFSET)
+/*
+* When 1, accesses to \Rdatazero cause the command in \Rcommand to be
+* executed again.
*
-* 0: Raise a debug exception. (Used when software wants to use the
-* trigger module without an external debugger attached.)
+* The same is true for other other autoexec bits: When 1, accesses to
+* {\tt data}N cause the command in \Rcommand to be executed again.
+ */
+#define DMI_ABSTRACTCS_AUTOEXEC0_OFFSET 8
+#define DMI_ABSTRACTCS_AUTOEXEC0_LENGTH 1
+#define DMI_ABSTRACTCS_AUTOEXEC0 (0x1 << DMI_ABSTRACTCS_AUTOEXEC0_OFFSET)
+/*
+* Gets set if an abstract command fails. No abstract command is
+* started until the value is reset to 0.
*
-* 1: Enter Debug Mode. (Only supported when \Fdmode is 1.)
+* 0 (none): No error.
*
-* 2: Start tracing.
+* 1 (busy): An abstract command was executing while \Rcommand or one
+* of the {\tt data} registers was accessed.
*
-* 3: Stop tracing.
+* 2 (not supported): The requested command is not supported. A
+* command that is not supported while the hart is running may be
+* supported when it is halted.
*
-* 4: Emit trace data for this match. If it is a data access match,
-* emit appropriate Load/Store Address/Data. If it is an instruction
-* execution, emit its PC.
+* 3 (exception): An exception occurred while executing the command
+* (eg. while executing the Program Buffer).
*
-* Other values are reserved for future use.
+* 4 (halt/resume): An abstract command couldn't execute because the
+* hart wasn't in the expected state (running/halted).
+*
+* 7 (other): The command failed for another reason.
*/
-#define CSR_ICOUNT_ACTION_OFFSET 0
-#define CSR_ICOUNT_ACTION_LENGTH 6
-#define CSR_ICOUNT_ACTION (0x3fL << CSR_ICOUNT_ACTION_OFFSET)
-#define DTM_IDCODE 0x01
+#define DMI_ABSTRACTCS_CMDERR_OFFSET 5
+#define DMI_ABSTRACTCS_CMDERR_LENGTH 3
+#define DMI_ABSTRACTCS_CMDERR (0x7 << DMI_ABSTRACTCS_CMDERR_OFFSET)
+/*
+* 1: An abstract command is currently being executed.
+*
+* This bit is set as soon as \Rcommand is written, and isn't cleared
+* until that command has completed.
+ */
+#define DMI_ABSTRACTCS_BUSY_OFFSET 4
+#define DMI_ABSTRACTCS_BUSY_LENGTH 1
+#define DMI_ABSTRACTCS_BUSY (0x1 << DMI_ABSTRACTCS_BUSY_OFFSET)
+/*
+* Number of {\tt data} registers that are implemented as part of the
+* abstract command interface. If it's 0 then no abstract interface is
+* implemented at all.
+ */
+#define DMI_ABSTRACTCS_DATACOUNT_OFFSET 0
+#define DMI_ABSTRACTCS_DATACOUNT_LENGTH 4
+#define DMI_ABSTRACTCS_DATACOUNT (0xf << DMI_ABSTRACTCS_DATACOUNT_OFFSET)
+#define DMI_COMMAND 0x0f
+/*
+* The type determines the overall functionality of this
+* abstract command.
+ */
+#define DMI_COMMAND_TYPE_OFFSET 24
+#define DMI_COMMAND_TYPE_LENGTH 8
+#define DMI_COMMAND_TYPE (0xff << DMI_COMMAND_TYPE_OFFSET)
+/*
+* This field is interpreted in a command-specific manner,
+* described for each abstract command.
+ */
+#define DMI_COMMAND_CONTROL_OFFSET 0
+#define DMI_COMMAND_CONTROL_LENGTH 24
+#define DMI_COMMAND_CONTROL (0xffffff << DMI_COMMAND_CONTROL_OFFSET)
+#define DMI_DATA0 0x10
+#define DMI_DATA0_DATA_OFFSET 0
+#define DMI_DATA0_DATA_LENGTH 32
+#define DMI_DATA0_DATA (0xffffffff << DMI_DATA0_DATA_OFFSET)
+#define DMI_DATA1 0x11
+#define DMI_DATA2 0x12
+#define DMI_DATA3 0x13
+#define DMI_DATA4 0x14
+#define DMI_DATA5 0x15
+#define DMI_DATA6 0x16
+#define DMI_DATA7 0x17
+#define DMI_DATA8 0x18
+#define DMI_DATA9 0x19
+#define DMI_DATA10 0x1a
+#define DMI_DATA11 0x1b
+#define DMI_SERDATA 0x1c
+#define DMI_SERDATA_DATA_OFFSET 0
+#define DMI_SERDATA_DATA_LENGTH 32
+#define DMI_SERDATA_DATA (0xffffffff << DMI_SERDATA_DATA_OFFSET)
+#define DMI_SERCS 0x1d
/*
-* Identifies the release version of this part.
+* Number of supported serial ports.
*/
-#define DTM_IDCODE_VERSION_OFFSET 28
-#define DTM_IDCODE_VERSION_LENGTH 4
-#define DTM_IDCODE_VERSION (0xf << DTM_IDCODE_VERSION_OFFSET)
+#define DMI_SERCS_SERIALCOUNT_OFFSET 28
+#define DMI_SERCS_SERIALCOUNT_LENGTH 4
+#define DMI_SERCS_SERIALCOUNT (0xf << DMI_SERCS_SERIALCOUNT_OFFSET)
/*
-* Identifies the designer's part number of this part.
+* Select which serial port is accessed by \Rserdata.
*/
-#define DTM_IDCODE_PARTNUMBER_OFFSET 12
-#define DTM_IDCODE_PARTNUMBER_LENGTH 16
-#define DTM_IDCODE_PARTNUMBER (0xffff << DTM_IDCODE_PARTNUMBER_OFFSET)
+#define DMI_SERCS_SERIAL_OFFSET 16
+#define DMI_SERCS_SERIAL_LENGTH 3
+#define DMI_SERCS_SERIAL (0x7 << DMI_SERCS_SERIAL_OFFSET)
+#define DMI_SERCS_VALID7_OFFSET 15
+#define DMI_SERCS_VALID7_LENGTH 1
+#define DMI_SERCS_VALID7 (0x1 << DMI_SERCS_VALID7_OFFSET)
+#define DMI_SERCS_FULL_OVERFLOW7_OFFSET 14
+#define DMI_SERCS_FULL_OVERFLOW7_LENGTH 1
+#define DMI_SERCS_FULL_OVERFLOW7 (0x1 << DMI_SERCS_FULL_OVERFLOW7_OFFSET)
+#define DMI_SERCS_VALID6_OFFSET 13
+#define DMI_SERCS_VALID6_LENGTH 1
+#define DMI_SERCS_VALID6 (0x1 << DMI_SERCS_VALID6_OFFSET)
+#define DMI_SERCS_FULL_OVERFLOW6_OFFSET 12
+#define DMI_SERCS_FULL_OVERFLOW6_LENGTH 1
+#define DMI_SERCS_FULL_OVERFLOW6 (0x1 << DMI_SERCS_FULL_OVERFLOW6_OFFSET)
+#define DMI_SERCS_VALID5_OFFSET 11
+#define DMI_SERCS_VALID5_LENGTH 1
+#define DMI_SERCS_VALID5 (0x1 << DMI_SERCS_VALID5_OFFSET)
+#define DMI_SERCS_FULL_OVERFLOW5_OFFSET 10
+#define DMI_SERCS_FULL_OVERFLOW5_LENGTH 1
+#define DMI_SERCS_FULL_OVERFLOW5 (0x1 << DMI_SERCS_FULL_OVERFLOW5_OFFSET)
+#define DMI_SERCS_VALID4_OFFSET 9
+#define DMI_SERCS_VALID4_LENGTH 1
+#define DMI_SERCS_VALID4 (0x1 << DMI_SERCS_VALID4_OFFSET)
+#define DMI_SERCS_FULL_OVERFLOW4_OFFSET 8
+#define DMI_SERCS_FULL_OVERFLOW4_LENGTH 1
+#define DMI_SERCS_FULL_OVERFLOW4 (0x1 << DMI_SERCS_FULL_OVERFLOW4_OFFSET)
+#define DMI_SERCS_VALID3_OFFSET 7
+#define DMI_SERCS_VALID3_LENGTH 1
+#define DMI_SERCS_VALID3 (0x1 << DMI_SERCS_VALID3_OFFSET)
+#define DMI_SERCS_FULL_OVERFLOW3_OFFSET 6
+#define DMI_SERCS_FULL_OVERFLOW3_LENGTH 1
+#define DMI_SERCS_FULL_OVERFLOW3 (0x1 << DMI_SERCS_FULL_OVERFLOW3_OFFSET)
+#define DMI_SERCS_VALID2_OFFSET 5
+#define DMI_SERCS_VALID2_LENGTH 1
+#define DMI_SERCS_VALID2 (0x1 << DMI_SERCS_VALID2_OFFSET)
+#define DMI_SERCS_FULL_OVERFLOW2_OFFSET 4
+#define DMI_SERCS_FULL_OVERFLOW2_LENGTH 1
+#define DMI_SERCS_FULL_OVERFLOW2 (0x1 << DMI_SERCS_FULL_OVERFLOW2_OFFSET)
+#define DMI_SERCS_VALID1_OFFSET 3
+#define DMI_SERCS_VALID1_LENGTH 1
+#define DMI_SERCS_VALID1 (0x1 << DMI_SERCS_VALID1_OFFSET)
+#define DMI_SERCS_FULL_OVERFLOW1_OFFSET 2
+#define DMI_SERCS_FULL_OVERFLOW1_LENGTH 1
+#define DMI_SERCS_FULL_OVERFLOW1 (0x1 << DMI_SERCS_FULL_OVERFLOW1_OFFSET)
/*
-* Identifies the designer/manufacturer of this part. Bits 6:0 must be
-* bits 6:0 of the designer/manufacturer's Identification Code as
-* assigned by JEDEC Standard JEP106. Bits 10:7 contain the modulo-16
-* count of the number of continuation characters (0x7f) in that same
-* Identification Code.
+* 1 when the core-to-debugger queue for serial port 0 is not empty.
*/
-#define DTM_IDCODE_MANUFID_OFFSET 1
-#define DTM_IDCODE_MANUFID_LENGTH 11
-#define DTM_IDCODE_MANUFID (0x7ff << DTM_IDCODE_MANUFID_OFFSET)
-#define DTM_IDCODE_1_OFFSET 0
-#define DTM_IDCODE_1_LENGTH 1
-#define DTM_IDCODE_1 (0x1 << DTM_IDCODE_1_OFFSET)
-#define DTM_SAMPLE 0x02
-#define DTM_PRELOAD 0x03
-#define DTM_EXTEST 0x04
-#define DTM_CLAMP 0x05
-#define DTM_CLAMP__HOLD 0x06
-#define DTM_CLAMP__RELEASE 0x07
-#define DTM_HIGHZ 0x08
-#define DTM_IC__RESET 0x09
-#define DTM_TMP__STATUS 0x0a
-#define DTM_INIT__SETUP 0x0b
-#define DTM_INIT__SETUP__CLAMP 0x0c
-#define DTM_INIT__RUN 0x0d
-#define DTM_DTMCONTROL 0x10
+#define DMI_SERCS_VALID0_OFFSET 1
+#define DMI_SERCS_VALID0_LENGTH 1
+#define DMI_SERCS_VALID0 (0x1 << DMI_SERCS_VALID0_OFFSET)
/*
-* Writing 1 to this bit resets the DMI controller, clearing any
-* sticky error state.
+* 1 when the debugger-to-core queue for serial port 0 is either full,
+* or has overflowed. Overflow state is sticky, and can be reset by
+* writing 0 to this bit.
*/
-#define DTM_DTMCONTROL_DMIRESET_OFFSET 16
-#define DTM_DTMCONTROL_DMIRESET_LENGTH 1
-#define DTM_DTMCONTROL_DMIRESET (0x1 << DTM_DTMCONTROL_DMIRESET_OFFSET)
+#define DMI_SERCS_FULL_OVERFLOW0_OFFSET 0
+#define DMI_SERCS_FULL_OVERFLOW0_LENGTH 1
+#define DMI_SERCS_FULL_OVERFLOW0 (0x1 << DMI_SERCS_FULL_OVERFLOW0_OFFSET)
+#define DMI_PROGBUFCS 0x1f
/*
-* This is the minimum number of cycles a debugger should spend in
-* Run-Test/Idle after every DMI scan to avoid a 'busy'
-* return code (\Fdmistat of 3). A debugger must still
-* check \Fdmistat when necessary.
-*
-* 0: It is not necessary to enter Run-Test/Idle at all.
-*
-* 1: Enter Run-Test/Idle and leave it immediately.
+* Size of the Program Buffer, in 32-bit words. Valid sizes are 0 - 12.
*
-* 2: Enter Run-Test/Idle and stay there for 1 cycle before leaving.
+* A debugger must not access any Program Buffer locations that
+* fall outside the range specified here.
*
-* And so on.
+* TODO: Explain what can be done with each size of the buffer, to suggest
+* why you would want more or less words.
*/
-#define DTM_DTMCONTROL_IDLE_OFFSET 12
-#define DTM_DTMCONTROL_IDLE_LENGTH 3
-#define DTM_DTMCONTROL_IDLE (0x7 << DTM_DTMCONTROL_IDLE_OFFSET)
+#define DMI_PROGBUFCS_PROGSIZE_OFFSET 0
+#define DMI_PROGBUFCS_PROGSIZE_LENGTH 4
+#define DMI_PROGBUFCS_PROGSIZE (0xf << DMI_PROGBUFCS_PROGSIZE_OFFSET)
+#define DMI_PROGBUF0 0x20
+#define DMI_PROGBUF0_DATA_OFFSET 0
+#define DMI_PROGBUF0_DATA_LENGTH 32
+#define DMI_PROGBUF0_DATA (0xffffffff << DMI_PROGBUF0_DATA_OFFSET)
+#define DMI_PROGBUF1 0x21
+#define DMI_PROGBUF2 0x22
+#define DMI_PROGBUF3 0x23
+#define DMI_PROGBUF4 0x24
+#define DMI_PROGBUF5 0x25
+#define DMI_PROGBUF6 0x26
+#define DMI_PROGBUF7 0x27
+#define DMI_PROGBUF8 0x28
+#define DMI_PROGBUF9 0x29
+#define DMI_PROGBUF10 0x2a
+#define DMI_PROGBUF11 0x2b
+#define SERINFO 0x110
/*
-* 0: No error.
-*
-* 1: Reserved. Interpret the same as 2.
-*
-* 2: An operation failed (resulted in \Fop of 2).
-*
-* 3: An operation was attempted while a DMI access was still in
-* progress (resulted in \Fop of 3).
+* Like \Fserialzero.
*/
-#define DTM_DTMCONTROL_DMISTAT_OFFSET 10
-#define DTM_DTMCONTROL_DMISTAT_LENGTH 2
-#define DTM_DTMCONTROL_DMISTAT (0x3 << DTM_DTMCONTROL_DMISTAT_OFFSET)
+#define SERINFO_SERIAL7_OFFSET 7
+#define SERINFO_SERIAL7_LENGTH 1
+#define SERINFO_SERIAL7 (0x1 << SERINFO_SERIAL7_OFFSET)
/*
-* The size of \Faddress in \Rdmi.
+* Like \Fserialzero.
*/
-#define DTM_DTMCONTROL_ABITS_OFFSET 4
-#define DTM_DTMCONTROL_ABITS_LENGTH 6
-#define DTM_DTMCONTROL_ABITS (0x3f << DTM_DTMCONTROL_ABITS_OFFSET)
+#define SERINFO_SERIAL6_OFFSET 6
+#define SERINFO_SERIAL6_LENGTH 1
+#define SERINFO_SERIAL6 (0x1 << SERINFO_SERIAL6_OFFSET)
/*
-* 0: Version described in spec version 0.11.
-*
-* 1: Version described in spec version 0.12 (and later?), which
-* reduces the DMI data width to 32 bits.
-*
-* Other values are reserved for future use.
+* Like \Fserialzero.
*/
-#define DTM_DTMCONTROL_VERSION_OFFSET 0
-#define DTM_DTMCONTROL_VERSION_LENGTH 4
-#define DTM_DTMCONTROL_VERSION (0xf << DTM_DTMCONTROL_VERSION_OFFSET)
-#define DTM_DMI 0x11
+#define SERINFO_SERIAL5_OFFSET 5
+#define SERINFO_SERIAL5_LENGTH 1
+#define SERINFO_SERIAL5 (0x1 << SERINFO_SERIAL5_OFFSET)
/*
-* Address used for DMI access. In Update-DR this value is used
-* to access the DM over the DMI.
+* Like \Fserialzero.
*/
-#define DTM_DMI_ADDRESS_OFFSET 34
-#define DTM_DMI_ADDRESS_LENGTH abits
-#define DTM_DMI_ADDRESS (((1L<<abits)-1) << DTM_DMI_ADDRESS_OFFSET)
+#define SERINFO_SERIAL4_OFFSET 4
+#define SERINFO_SERIAL4_LENGTH 1
+#define SERINFO_SERIAL4 (0x1 << SERINFO_SERIAL4_OFFSET)
/*
-* The data to send to the DM over the DMI during Update-DR, and
-* the data returned from the DM as a result of the previous operation.
+* Like \Fserialzero.
*/
-#define DTM_DMI_DATA_OFFSET 2
-#define DTM_DMI_DATA_LENGTH 32
-#define DTM_DMI_DATA (0xffffffffL << DTM_DMI_DATA_OFFSET)
+#define SERINFO_SERIAL3_OFFSET 3
+#define SERINFO_SERIAL3_LENGTH 1
+#define SERINFO_SERIAL3 (0x1 << SERINFO_SERIAL3_OFFSET)
/*
-* When the debugger writes this field, it has the following meaning:
-*
-* 0: Ignore \Fdata. (nop)
-*
-* 1: Read from \Faddress. (read)
-*
-* 2: Write \Fdata to \Faddress. (write)
-*
-* 3: Reserved.
-*
-* When the debugger reads this field, it means the following:
-*
-* 0: The previous operation completed successfully.
-*
-* 1: Reserved.
-*
-* 2: The previous operation returned a non-zero value in \Fop.
-* The data scanned into \Rdmi in this access will be ignored.
-* This status is sticky and can be cleared by writing \Fdmireset
-* in \Rdtmcontrol.
-*
-* (This indicates that the DM itself responded with an error, e.g.
-* in the System Bus and Serial Port overflow/underflow cases.
-* Generally this means that for this type of DM access, the DTM should
-* allow more time between Update-DR and Capture-DR. The most portable way
-* to achieve this is to spend more TCK ticks in Run-Test/Idle state
-* for similar operations.)
-*
-* 3: The previous DMI request is still in progress. The data scanned
-* into \Rdmi in this access will be ignored. This status is sticky
-* and can be cleared by writing \Fdmireset in \Rdtmcontrol. If a
-* debugger sees this status, it needs to give the target more TCK
-* edges between Update-DR and Capture-DR. The simplest way
-* to do that is to add extra transitions in Run-Test/Idle.
-*
-* (The DTM, DM, and/or component may be in different clock domains,
-* so synchronization may be required. Some relatively fixed number of
-* TCK ticks may be needed for the request to reach the DM, complete,
-* and for the response to be synchronized back into the TCK domain.
-* This status is intended to cover these cases, and is orthogonal to
-* the causes for case 2.)
+* Like \Fserialzero.
*/
-#define DTM_DMI_OP_OFFSET 0
-#define DTM_DMI_OP_LENGTH 2
-#define DTM_DMI_OP (0x3L << DTM_DMI_OP_OFFSET)
-#define SHORTNAME 0x123
+#define SERINFO_SERIAL2_OFFSET 2
+#define SERINFO_SERIAL2_LENGTH 1
+#define SERINFO_SERIAL2 (0x1 << SERINFO_SERIAL2_OFFSET)
/*
-* Description of what this field is used for.
+* Like \Fserialzero.
*/
-#define SHORTNAME_FIELD_OFFSET 0
-#define SHORTNAME_FIELD_LENGTH 8
-#define SHORTNAME_FIELD (0xff << SHORTNAME_FIELD_OFFSET)
+#define SERINFO_SERIAL1_OFFSET 1
+#define SERINFO_SERIAL1_LENGTH 1
+#define SERINFO_SERIAL1 (0x1 << SERINFO_SERIAL1_OFFSET)
+/*
+* 1 means serial interface 0 is supported.
+ */
+#define SERINFO_SERIAL0_OFFSET 0
+#define SERINFO_SERIAL0_LENGTH 1
+#define SERINFO_SERIAL0 (0x1 << SERINFO_SERIAL0_OFFSET)
+#define SERSEND0 0x200
+#define SERRECV0 0x204
+#define SERSTAT0 0x208
+/*
+* Send ready. 1 when the core-to-debugger queue is not full. 0
+* otherwise.
+ */
+#define SERSTAT0_SENDR_OFFSET 1
+#define SERSTAT0_SENDR_LENGTH 1
+#define SERSTAT0_SENDR (0x1 << SERSTAT0_SENDR_OFFSET)
+/*
+* Receive ready. 1 when the debugger-to-core queue is not empty. 0
+* otherwise.
+ */
+#define SERSTAT0_RECVR_OFFSET 0
+#define SERSTAT0_RECVR_LENGTH 1
+#define SERSTAT0_RECVR (0x1 << SERSTAT0_RECVR_OFFSET)
+#define SERSEND1 0x20c
+#define SERRECV1 0x210
+#define SERSTAT1 0x214
+#define SERSEND2 0x218
+#define SERRECV2 0x21c
+#define SERSTAT2 0x220
+#define SERSEND3 0x224
+#define SERRECV3 0x228
+#define SERSTAT3 0x22c
+#define SERSEND4 0x230
+#define SERRECV4 0x234
+#define SERSTAT4 0x238
+#define SERSEND5 0x23c
+#define SERRECV5 0x240
+#define SERSTAT5 0x244
+#define SERSEND6 0x248
+#define SERRECV6 0x24c
+#define SERSTAT6 0x250
+#define SERSEND7 0x254
+#define SERRECV7 0x258
+#define SERSTAT7 0x25c
#define TRACE 0x728
/*
* 1 if the trace buffer has wrapped since the last time \Fdiscard was
#define TBUFSTART 0x729
#define TBUFEND 0x72a
#define TBUFWRITE 0x72b
+#define SHORTNAME 0x123
+/*
+* Description of what this field is used for.
+ */
+#define SHORTNAME_FIELD_OFFSET 0
+#define SHORTNAME_FIELD_LENGTH 8
+#define SHORTNAME_FIELD (0xff << SHORTNAME_FIELD_OFFSET)
+#define AC_ACCESS_REGISTER None
+/*
+* This is 0 to indicate Access Register Command.
+ */
+#define AC_ACCESS_REGISTER_TYPE_OFFSET 24
+#define AC_ACCESS_REGISTER_TYPE_LENGTH 8
+#define AC_ACCESS_REGISTER_TYPE (0xff << AC_ACCESS_REGISTER_TYPE_OFFSET)
+/*
+* 2: Access the lowest 32 bits of the register.
+*
+* 3: Access the lowest 64 bits of the register.
+*
+* 4: Access the lowest 128 bits of the register.
+*
+* If \Fsize specifies a size larger than the register is, then the
+* access must fail. If a register is accessible, then \Fsize matching
+* the register's actual size must be supported.
+ */
+#define AC_ACCESS_REGISTER_SIZE_OFFSET 19
+#define AC_ACCESS_REGISTER_SIZE_LENGTH 3
+#define AC_ACCESS_REGISTER_SIZE (0x7 << AC_ACCESS_REGISTER_SIZE_OFFSET)
+/*
+* When 1, execute the program in the Program Buffer exactly once
+* before performing the read/write.
+ */
+#define AC_ACCESS_REGISTER_PREEXEC_OFFSET 18
+#define AC_ACCESS_REGISTER_PREEXEC_LENGTH 1
+#define AC_ACCESS_REGISTER_PREEXEC (0x1 << AC_ACCESS_REGISTER_PREEXEC_OFFSET)
+/*
+* When 1, execute the program in the Program Buffer exactly once
+* after performing the read/write.
+ */
+#define AC_ACCESS_REGISTER_POSTEXEC_OFFSET 17
+#define AC_ACCESS_REGISTER_POSTEXEC_LENGTH 1
+#define AC_ACCESS_REGISTER_POSTEXEC (0x1 << AC_ACCESS_REGISTER_POSTEXEC_OFFSET)
+/*
+* 0: Copy data from the specified register into {\tt arg0} portion
+* of {\tt data}.
+*
+* 1: Copy data from {\tt arg0} portion of {\tt data} into the
+* specified register.
+ */
+#define AC_ACCESS_REGISTER_WRITE_OFFSET 16
+#define AC_ACCESS_REGISTER_WRITE_LENGTH 1
+#define AC_ACCESS_REGISTER_WRITE (0x1 << AC_ACCESS_REGISTER_WRITE_OFFSET)
+/*
+* Number of the register to access, as described in Table~\ref{tab:regno}.
+ */
+#define AC_ACCESS_REGISTER_REGNO_OFFSET 0
+#define AC_ACCESS_REGISTER_REGNO_LENGTH 16
+#define AC_ACCESS_REGISTER_REGNO (0xffff << AC_ACCESS_REGISTER_REGNO_OFFSET)
+#define AC_QUICK_ACCESS None
+/*
+* This is 1 to indicate Quick Access command.
+ */
+#define AC_QUICK_ACCESS_TYPE_OFFSET 24
+#define AC_QUICK_ACCESS_TYPE_LENGTH 8
+#define AC_QUICK_ACCESS_TYPE (0xff << AC_QUICK_ACCESS_TYPE_OFFSET)
projects / riscv-isa-sim.git / commitdiff